Caterpillar WHEEL-TYPE LOADER 924GZ - catalog of spare parts
Bucket
Mine clearance at Max Raise - 9.06 feet in
Dimensions
Length with bucket on the ground - 23.1 feet in
Tire Width - 7.8 Feet in
Height to Cab Top - 10.6 ft.
Total height - 15.7 feet in
Ground clearance - 1.2 feet in
Wheelbase - 9.2 feet in
Articulated Finger - Maximum Height - 12.4 Feet
Reach in Max Lift and Dump - 2.9 feet in
Total length - 23.1 feet in
Wheelbase - 9.2 feet in
Height - Top Hood - 85.2 inches
Dump angle at maximum lift - 45 degrees
Width - Over Tires - 7.9 Feet in
Height - Top ROPS / FOPS - 10.5 ft.
Height - Top of Exhaust Pipe - 10.4 Feet
Height - Center Axis - 2.1 Feet
Centerline from front axle to hitch - 4.7 ft.
Wheelbase 9.2 ft. In
Ground clearance at maximum lift - 45 degrees - 9.1 feet in
Bucket Clearance - Maximum Lift / Carry - 11.1 ft.
Reach at the Maximum Lift and 45 Degree Dump - 2.1 feet in
A-pillar angle - maximum lift - 58 degrees
Rear corner of the rack - ground - 44 degrees
Rear Post Angle - Wear - 48 degrees
Bearing Height - 1.2 feet in
Total Height - Bucket Raised - 15.7 Feet in
Bucket Finger Height - Maximum Lifting Height - 12.1 Feet
Length - from rear axle to bumper - 6.4 ft.
Digging Depth - 4 inches
Choose WHEEL-TYPE LOADER 924GZ section:
Specifications
engine
Engine Model - 3056T
Net power - 130hp
Gross Power - 138 HP
Measured Power @ - 2300 rpm
Displacement - 366cu in
4 inch diameter
Stroke - 5 inches
Rated net power - 129hp
SAE J1349 (2) - 137 HP
ISO 9249 (1997) (2) - 138 h.p.
EEC 80/1269 (2) - 138 HP
SAE J1349 (1) - 129 HP
ISO 9249 (1997) (1) - 130 HP
EEC 80/1269 (1) - 130 HP
Operational
Working Weight - 23,920.2 lbs.
59.5 gallon fuel tank capacity
Hydraulic system capacity - 33.1 gallons
5.3 gallon engine oil
Cooling system capacity - 10.6 gal
Transmission fluid capacity - 6.1 gal
5.6 gallon front axle / differential fluid volume
Rear Axle / Differential Fluid Capacity - 5.6 gallons
Turn radius - 16.7 feet in
Dimensions
Length with bucket on the ground - 23.07 feet in
Tire Width - 7.73 Feet in
Height to Cab Top - 10.6 ft.
Wheelbase - 9.19 feet in
Ground clearance - 1.2 feet in
Articulated Finger - Maximum Height - 12.34 Feet
Reach in Max Lift and Dump - 2.84 feet in
Transmission
The number of forward gears - 4
Number of reverse gears - 3
Top Speed - Forward - 24.3 mph
Max. Speed - Reverse - 13.5 mph
Forward - 1 (1) - 4.2 miles per hour
Reverse - 1 (1) - 4.2 miles per hour
Forward - 1 (2) - 2.3 miles per hour
2 (2) - 4.7 mph
3 (2) - 12.2 mph
4 (2) - 24.2 miles per hour
Reverse - 1 (2) - 2.5 miles per hour
2 (3) - 5 miles per hour
3 (3) - 13.2 mph
2 (1) - 7.6 mph
3 (1) - 13.5 mph
4 (1) - 23.9 mph
Steering
Turning angle - in each direction - 40 degrees
Minimum turning radius - above tires - 200 inches
Steering Cylinder, Two, 2.8 inch Hole
Hydraulic power at 2300 rpm of the engine and 6900 kPa (1000 psi) - 27.7 gallons / min
Maximum working pressure - 3000 psi
Weights
Working Weight - 23,920 lbs.
Tires
Tread Width - 6.2 Feet in
Size - 17.5-25PR (L-2)
Buckets
Bucket capacity M 1.7 m3 - 2.1 m3 2.2 yards 3 - 2.7 cubic meters
Hydraulic system
Pump Type - Load Sensitive Hydraulic
Installation of a safety valve - 3756.5
Pump productivity - 40.2 gal / min
Raise Time - 5.5sec
Dump time - 1.2 sec.
Shorter time - 2.7 s
Bucket
Breakout Power - 21,727 pounds
Dump clearance at maximum lift - 9.1 feet per
Bucket Width - 8.4 Feet in
Bucket capacity - bulk - 2yd3
Axes
Axis Swing - 12 degrees
Performance characteristics
Static Tipping Load - Full Turn - 15,163 lbs.
Breakout Power - 21,727 pounds
Joint angle - 40 degrees
Achieve - Full Ascent and 45 Degree Dump - 2.1 Feet
Unloading clearance at full lift and a dump angle of 45 degrees - 9.1 feet per
Bucket Capacity - with bolt-on cutting edge - 2yd3
Service replenishment options
Cooling system - 10.9 gal
Fuel Tank - 59.4 Gallons
Carter - 4.2gal
Hydraulic Tank - 18.5 Gallon
Hydraulic system - including tank - 33gal
Gearbox - 6.1gal
Front - 5.5gal
Rear - 5.5gal
Taxi
ROPS - SAE J1040 MAY94, ISO 3471-1994
FOPS - SAE J231 JAN81, ISO 3449-1992 Level II
Loader hydraulic system
Pump Consumption - Implement Pump - 40.15 gal / min
Productivity at 2300 rpm of the engine and 6900 kPa (1000 psi) when using SAE 10 W oil at a temperature of 65 degrees C (150 degrees F) - 39.5 gallons / min.
Maximum Working Pressure - 3,755 psi
Rise - 5.2 s
Blade - 1.1 s
Lower, lower, lower - 2.7 s
Total - 9 s
Hole (1) - 4.3 inches
Stroke (1) - 29.7 inches
Hole (2) - 4.8 inches
Stroke (2) - 20.5 inches