Caterpillar WHEEL-TYPE LOADER 906M - catalog of spare parts
Loader hydraulic system
Double Acting Lifting Cylinder - Stroke - 27.4 Inches
Double Action Tilt Cylinder - Stroke - 16.4in
Maximum Consumption - Gun Pump - 19 gal / min
3rd Function Maximum Pressure - 3408 psi
Maximum Working Pressure - Implement Pump - 3408 psi
Pressure Relief - Tilt Cylinder Rod - 2756 psi
Maximum boost pressure - 3191 psi
Double Acting Lifting Cylinder - 3 Inch Diameter
Double Acting Lifting Cylinder - Bar Diameter - 2 Inches
Double acting tilt cylinder - bore diameter - 3.5 inches
Double Action Tilt Cylinder - Rod Diameter - 2.2 Inches
Hydraulic cycle time - 1800 rpm - rise, ground level to maximum rise - 5.5 s
Hydraulic cycle time - 1800 rpm - unloading at a maximum lift height - 1.5 s
Hydraulic cycle time - 1800 rpm - swimming down, maximum rise to ground level - 2.6 s
Hydraulic cycle time - 1800 rpm - Total cycle time - 9.6 s
Hydraulic cycle time - 1000 rpm - rise, ground level to maximum rise - 9.6 s
Hydraulic cycle time - 1000 rpm - unloading at maximum lift height - 3 s
Hydraulic cycle time - 1000 rpm - swimming down, maximum rise to ground level - 2.6 s
Maximum flow rate - Implement pump - Auxiliary function Standard flow rate - 19 gal / min
Maximum flow rate - Implement pump - Auxiliary function High flow rate - 31 gallons / min
Pressure Relief - Tilt Cylinder Head - 4,496 psi
Choose WHEEL-TYPE LOADER 906M section:
Specifications
engine
Net power - 74 hp
Displacement - 201cu per
Hole - 3.7 inches
4.7 inch travel
Emissions
* Cat C3.3B DIT engine complies with US EPA Tier 4 Final / EU Stage IIIB emission standards or equivalent Tier 4 Interim / Stage IIIA emission standards.
Engine Model - Cat C3.3B DIT *
Note (1) - The net power ratings are tested under standard conditions for the specified standard.
Note (2) - The net power shown is the power available on the flywheel when the engine is equipped with an alternator, air cleaner, exhaust filter and fan at minimum speed.
Note (3) - No degradation is required at altitudes up to 3,000 m (10,000 ft). Auto derate protects hydraulic and transmission systems.
Note (4) - Flywheel in accordance with the SAE baseline conditions with fan at maximum speed.
Maximum apparent power - SAE J1995 - 74 hp
Maximum apparent power - ISO 14396 - 73 hp
Maximum gross power - 73 hp
Maximum apparent power - ISO 14396 (DIN) - 74 hp
Maximum Torque - ISO 14396 - 192 lb-ft
Maximum Net Torque - SAE J1349 - 189 lb-ft
Maximum Net Torque - ISO 9249 (1977) / EEC 80/1269 - 191 lb-ft
Note (5)
The Cat C3.3B Tier 4 Final / Stage IIIB uses an active regeneration system that does not require operator interaction under normal conditions.
Rated net power - 2400 rpm - SAE J1349 - 73 hp
Rated net power - 2400 rpm - ISO 9249 (1977) / EEC 80/1269 - 74 hp
A train
Forward - Range 1 - 6 mph
Forward - Range 2 - 12 mph
Ahead - High Range - 22 mph
Reverse - Range 1 - 6 mph
Reverse - Range 2 - 12 mph
Reverse - High Range - 22 mph
Operational
Working Weight - 12,346 lbs
Steering
Maximum Working Pressure - Steering Pump - 3191 psi
Steering joint angle - in each direction - 39 degrees
Double Acting Steering Cylinder - Bore Diameter - 3.1in
Double Acting Steering Cylinder - 1.4 Inch Diameter
Double Acting Steering Cylinder - Stroke - 11.8 Inches
Nominal flow rate - steering pump - 12 gal / min
Maximum Steering Torque - 0 Degrees (Direct Machine) - 37,155 lb ft
Maximum Steering Torque - 39 Degrees (Full Turn) - 27,747 lbs / ft
Steering AC cycle time - from full left to full right - 2620 rpm - 3 s
The number of revolutions of the steering wheel - from full left to full right or from full right to full left - <6 turns
Weights
The note
The technical specifications presented apply to a machine equipped with general purpose buckets, bolt-on cutting edges, an operator weighing 75 kg (165 lbs), Dunlop 405/70 SPT9 tires, full fuel, a comfortable EROPS cab, standard flow hydraulics and an on-board turn coupling. - The 906M is equipped with a 0.9 m3 (1.2 cubic inch) bucket with bolt-on cutting edge.
Tires
Note (1) - * Standard bus.
Note (2) - Other tire options are available; contact your Cat dealer for details.
Note (3) - In some cases, the truck’s production capacity may exceed the tire capacity in tons / hour (t / mph).
Option (1) - 335/80 R18 XZSL Michelin
Option (2) - 340/80 R18 AT-R Firestone
Option (3) - 340/80 R18 XMCL Michelin
Option (4) - 340/80 R18 TRI2 Nokian
Option (5) - 340/80 R18 Bibload Michelin
Option (6) - 405/70 R18 SPT9 Dunlop *
Option (7) - 12.5 / 80 R18 Flexport
Note (4) - Caterpillar recommends consulting your tire supplier to evaluate all conditions before choosing a tire model.
Buckets
Bucket volume - 0.75 m3-1.2 m3 (1.0 g3-1.6 m 3)
General Purpose - 1.2 m
Lightweight Material - 1.6yd3
Performance characteristics
Nominal bucket capacity - 1.2yd3
7507 lb Tipping Load
Tipping Load - Direct - ISO 14397-1 - 8666 lbs.
Tipping Load - Full Turn - ISO 14397-1 - 7061 lbs
Ground clearance - full lift and 45-degree drop - 8.3 feet per
Achieve - full lift and 45-degree drop - 2.4 feet in
Steering joint angle - in each direction - 39 degrees
Service replenishment options
Cooling system - 4.4 gal
Fuel tank - 13.7 gal
Hydraulic Tank - 12.2 Gallons
Hydraulic system - including tank - 18.5 gallon
Crankcase - 3gal
Gearbox - gearbox - 2.2gal
Taxi
ROPS - SAE J1040 MAY94, ISO 3471-1994.
FOPS - SAE J / ISO 3449 APR98, Level II, ISO 3449 1992 Level II.
Note (1) - Cat cab and roll over protective structures (ROPS) are standard in North America and Europe.
Note (2) - When properly installed and serviced, the Caterpillar cab, when tested with doors and windows closed in accordance with the duty cycle procedures specified in ISO 6395 2008, results in sound exposure to the Leq operator (equivalent sound level pressure) is 66 dB (A) typical.
Dimensions with Bucket (approximate) - Standard Lift - With ISO Coupling
Height - From Ground to Cabin ** - 8.1 feet in
Height - ground clearance ** - 1 foot in
Length - Wheelbase - 7.1 Feet in
Length - Total * - 18 ft. In
Reach - Bucket 45 degrees * - 2.4 feet per
Digging Depth ** - 3.7 inches
Ground clearance - bucket at 45 degrees * - 8.1 feet per
Ground clearance - level bucket ** - 10 feet in
Height - Bucket Pin ** - 10.6 ft.
Width - Bucket - 6.2 Feet in
Width - Tread Center - 4.6 feet in
Turn radius - above bucket - 14.5 feet per
Turning radius - inside tires - 7.4 feet per
Machine Width - 6 Feet in
Dump angle at full rise - 45 degrees
Departure angle - 33 degrees
Joint angle - 39 degrees
Note (1) - * Depends on the bucket.
Note (2) - ** Bus dependent.
Note (3). The dimensions shown are for a machine with general purpose buckets, bolt-on cutting edges, an operator weighing 75 kg (165 lbs), no air conditioning, and Dunlop 405/70 SPT9 tires.
Dimensions with Bucket (approximate) - Standard Lift - With SSL Connector
Height - From Ground to Cabin ** - 8.1 feet in
Height - ground clearance ** - 1 foot in
Length - Wheelbase - 7.1 Feet in
Length - Total * - 18.5 feet in
Reach - Bucket 45 degrees * - 2.7 feet per
Digging Depth ** - 4.2 inches
Ground clearance - bucket at 45 degrees * - 7.7 feet per
Ground clearance - level bucket ** - 10 feet in
Height - Bucket Pin ** - 10.6 ft.
Width - Bucket - 6.2 Feet in
Width - Tread Center - 4.6 feet in
Turn radius - above bucket - 14.6 feet per
Turning radius - inside tires - 7.4 feet per
Machine Width - 6 Feet in
Dump angle at full rise - 45 degrees
Departure angle - 33 degrees
Joint angle - 9 degrees
Note (1) - * Depends on the bucket.
Note (2) - ** Bus dependent.
Note (3). The dimensions shown are for a machine with general purpose buckets, bolt-on cutting edges, an operator weighing 75 kg (165 lbs), no air conditioning, and Dunlop 405/70 SPT9 tires.