Caterpillar WHEEL-TYPE LOADER 906 - catalog of spare parts
Bucket
Dump clearance at maximum lift - 7.95 feet
Dimensions
Length with bucket on the ground - 16.54 feet in
Tire Width - 6.14 Feet
Height to Cab Top - 8.8 Feet in
Wheelbase - 6.5 feet in
Articulated Finger - Maximum Height - 10.25 Feet
Reach in Max Lift and Dump - 2.6 feet in
Choose WHEEL-TYPE LOADER 906 section:
Specifications
engine
Engine make - 2236
Engine Model - 3044C
Net power - 68hp
Gross Power - 75 HP
Measured Power @ - 2600 rpm
ISO 9249 Rating - 71 HP
EEC 80/1269 Rating - 71h.p.
SAE J1349 Rating - 71h.p.
Operational
Working Weight - 10912 lbs
The capacity of the fuel tank is 19.6 gal
Hydraulic Capacity 17.5 Gallons
Engine oil volume - 2.6gal
Cooling system capacity - 5.5gal
Transmission fluid capacity - 2.6gal
Static Tipping Weight - 7546 lbs
Operating voltage - 12 V
The amplifier from the generator - 90 amperes
Rear Axle Fluctuation - 22 degrees
Tire size - 12.5x18
Transmission
Transmission Type - Hydrostatic
The number of forward gears - 2
Number of reverse gears - 2
Top Speed - Forward - 12 Mph
Max. Speed - Reverse - 12 mph
Weights
Working Weight - 10912 lbs
Buckets
Bucket Width - 6.2 Feet in
Hydraulic system
Pump Type - Gear
Installation of a safety valve - 3408.4
Pump productivity - 18 gal / min
Lifting Time - 4.5sec
Dump time - 1.5 sec.
Shorter time - 3.2 s
Hydraulic Cycle Time - Dump - 1.5
Hydraulic Cycle Time - Lift - 4.5
The main relief is 3,400 psi
Hydraulic cycle time - lower, float - 3.2
3rd valve flow rate - 17.7 gal / min
Flow pressure at 2600 rpm and 70 bar (1000 psi) - 15.9 gallons per minute
Bucket
Breakout Force - 10,340 pounds
Unloading at Maximum Lift - 8 ft.
Bucket Width - 6.2 Feet in
Bucket Capacity - Bulk - 0.8yd3
Dimensions
Length with bucket on the ground - 16.6 feet in
Tire Width - 6.2 Feet in
Height to Cab Top - 8.8 Feet in
Wheelbase - 6.5 feet in
Articulated Finger - Maximum Height - 10.3 Feet
Reach in Max Lift and Dump - 2.6 feet in
Tread Width - 55 Inches
Performance characteristics
Breakout Force - 10,340 pounds
Nominal bucket capacity - 1.1yd3
Blade height at full lift - 8 ft.
Articulation - 40 degrees
Fluctuation +/- 11 degrees
Full Turn Static Tipping Load - Bucket - 6,666 lbs.
Stand back - transport position - 53 degrees
Rated Full Load Turnover Load - Bucket - 3,333 lbs.
9,100 lbs hydraulic lift capacity
Direct Tipping Load - Bucket - 7,546 pounds
Reach - Without Teeth - 2.8 Feet
Rated Full Load Turnover - Fork - 4,433 lbs
Full Turn Static Tipping Load - Fork - 5,500 pounds
Service replenishment options
Cooling system - 5.5gal
Fuel tank - 19.6 gal
Hydraulic system - 17.5 gal
Engine oil - 2.6gal
Taxi
ROPS - Meets the following criteria: SAE J1040 MAY94, ISO 3471-1: 1986
FOPS - Meets the following criteria: SAE J231 JAN81, ISO 3449: 1992
Sound - sound level below 75 dB (A)
Maximum material density
General Purpose Bucket - 0.6 m3 (0.8 yards3) - 3000 lbs / yard
Multipurpose Bucket - 0.6 m3 (0.8 yards3) - 3000 lbs / yard
Lightweight - 1.0 m3 (1.3 yards3) bucket - 1950 lbs / yard
Side Dump Bucket - 3000 lbs / yard
High Dump Bucket - 0.7 m3 (0.8 cubic feet) - 3200 lbs / sq.
Stone Screen Bucket - 0.6 m3 (0.8 yards) - 3300 lbs / yard
Motor dimensions
Hole - 3.7 inches
Powertrain, axles and brakes
Transmission type - two-stage hydrostatic single-pass transmission with a closed loop.
Maximum speeds - with tires 12.5-18, forward and backward, low - 4 mph
Top speed - forward and reverse, high - 12 miles per hour
Axle and final drives - fixed front axle with limited slip differential and planetary gear
Service and parking brake - combined into one, dry brake drive brake
Brake Standards - The brake complies with ISO 3450: 1996