Caterpillar WHEEL-TYPE LOADER 903C - catalog of spare parts
Dimensions
Length with bucket on the ground - 15.9 feet in
Height to Cab Top - 8.2 Feet in
Wheelbase - 5.9 ft. In
Ground clearance - 1.3 feet in
Articulated finger - maximum height - 10.6 feet per
Reach at Max Lift and Dump - 2.9 feet in
Bucket
Breakout Force - 5171 lbs.
Unloading clearance at maximum lift - 2.9 ft.
Bucket Width - 5.8 Feet in
Transmission
Travel Speed - 10 Mph
Weights
Operating Weight - 9150 pounds
Choose WHEEL-TYPE LOADER 903C section:
Engine
Engine make - 2236
Engine Model - C2.4
Net power - 40 hp
Gross Power - 42 HP
Displacement - 147cu per
Aspiration - Turbocharged
Hole Diameter 3.4
4 inch travel
Engine Model - Cat C2.4 *
Note - * Engine complies with US EPA Tier 4 Interim.
Net power - 2200 rpm - SAE J1349 rating - 40 hp
Net power - 2200 rpm - ISO 9249 rating - 40 hp
Net power - 2200 rpm - EEC rating 80/1269 - 40 hp
Operational
Operating Weight - 9150 pounds
11.4 gallon fuel tank capacity
Hydraulic capacity - 6.3 gal
Engine oil volume - 2.4gal
Cooling Capacity 3 Gallons
3,900 pounds static tipping weight
Operating voltage - 12 V
Generator current strength - 70 amperes
Tire size - 15.5-16.5
Buckets
Bucket volume - 0.6-1.0 m3 (0.8-1.3 cubic m)
Hydraulic system
Safety Valve Installation - 2988
Pump productivity - 14 gal / min
Raise Time - 4.7sec
Unloading time - 0.8 s
Lowering Time - 3.1sec
Hydraulic cycle time - dump - 0.8 s
Hydraulic Cycle Time - Rise - 4.7 s
The main relief is 2988 psi
3rd auxiliary stream - 14 gallons / min
Hydraulic cycle time - lower, float - 3.1 s
Dimensions
Length with bucket on the ground - 15.9 feet in
Height to Cab Top - 8.2 Feet in
Ground clearance - 1.3 feet in
Wheelbase - 5.9 ft. In
Articulated finger - maximum height - 10.6 feet per
Reach at Max Lift and Dump - 2.9 feet in
Operational characteristics
Breakout Force - 5171 lbs.
Nominal bucket capacity - 0.8yd3
Tire size - 33 15,5-16,5, 12PR
Standard - Operating Weight - 9150 lbs.
Standard - Nominal Full Load Turn Load - Bucket - 1950 lbs
Standard - Direct Tipping Load, 4,650 lb Bucket
Standard - Static Tipping Load - Full Turn, Bucket - 3,900 lbs.
Standard - Rackback, Transport Position - 52
Standard - Nominal Working Load per Full Turn - Fork (EN 474-3: 2006, Hard and Flat Surface, 500 mm (20 in) Load Center) (80% of FTSTL) - 2,500 lbs.
Standard - Nominal full-revolution workload - forks (EN 474-3: 2006, rough terrain, 500 mm (20 in.) With load center) (60% of FTSTL) - 1,900 pounds
With additional counterweight - Operating Weight - 9,500 lbs.
With optional counterweight - Nominal full-revolution workload - Bucket - 2,100 pounds
With optional counterweight - direct tipping load - 5,000 lb bucket
With additional counterweight - static tipping load per revolution - bucket - 4,200 pounds
With additional counterweight - Rackback - Transport position - 52
With additional counterweight - nominal full-revolution working load - forks (EN 474-3: 2006, firm and flat surface, 500 mm (20 in) load center) (80% of FTSTL) - 2,700 pounds
With additional counterweight - nominal full-revolution working load - forks (EN 474-3: 2006, rough terrain, load center 500 mm (20 inches)) (60% of FTSTL) - 2,000 pounds
Service replenishment options
Cooling system - 3gal
Fuel Tank - 11.4 Gallons
Hydraulic system - 6.3 gal
Engine oil - 2.4gal
Dimensions (approximate)
Ground clearance - 1.3 feet in
Wheelbase - 5.9 feet in
Cab Height - 8.2 Feet in
Total length - with bucket - 15.9 feet in
Departure at a maximum blade height of 2.9 feet
Digging Depth - 8 inches
Maximum blade height - 8 feet in
Height Load - 9.6 ft.
Hinge pin at maximum height - 10.6 feet per
Departure angle - 30
Total length - with forks - 17.4 feet in
Reach - ground level - 3.7 feet in
Maximum Departure - 5.4 Feet
Fork Depth Above Ground - 2 Inches
Fork Height at Maximum Departure - 4.7 Feet
Maximum fork height - 10.3 feet in
Departure forks at maximum height - 2.5 feet in
Turn Radius - Above Bucket - 13.2 ft.
Turn Radius - Internal Tire - 5.4 ft.
Width - Bucket - 5.8 Feet in
Tire measure - 4.3 feet in
Machine Width - 12-16.5 Tires 10PR - 5.4 feet in
Machine Width - Density 33-15.5 16.5 Tires - 5.6 feet per
Machine Width - Flexport 33 6 11 Tires - 5.2 Feet
Joint angle - 40
Steering angle - left / right - 80
Dropping angle at maximum height - 40
Taxi
ROPS - ISO 3471: 2008
FOPS - ISO 3449: 2000 Level I
Maximum material density
NOTE Based on ISO 7546: 1983 and rated working loads per revolution and without additional counterweight.
General Purpose - Bucket Type - General Purpose
General Purpose - Rated Power - 0.8yd3
General Purpose - Blade Height - 96 Inches
General Purpose - Maximum Material Density - 2437 lbs / yard
General Purpose - Bucket Width - 70 Inches
Lightweight Material - Bucket Type - Lightweight Material
Lightweight Material - Nominal Capacity - 1.3yd3
Lightweight - Blade Height - 91 Inch
Lightweight - Maximum Material Density - 1,423 lbs / yard
Lightweight Material - Bucket Width - 74 Inches