Caterpillar WHEEL TRACTOR-SCRAPER 623K - catalog of spare parts

 

Motor overspeed protection - in case of engine overspeed, the compression brake or brakes are automatically activated without operator intervention. The machine determines the overspeed condition based on the acceleration speed and automatically activates the compression brakes.

 

Advanced hitch - thanks to technology similar to Cat® Advanced Ride Management seat suspension, this software allows the cushion suspension device to prevent the final stroke, being able to predict the final stroke events and control the speed of the damping. The desired result is improved hitch repair, reduced maintenance and an improved operator ride in rough conditions.

High Pressure Steering - The design of the 620K Series steering system requires significantly less effort when taxiing. Reduced steering effort will reduce operator fatigue and increase its efficiency, which will lead to possible higher production rates at the end of the operating cycle.

The Load Assist - 623K option is now available with the Load Assist option, such as 621K and 627K.

Overflow protection - Now open bowls are now standard with overflow protection on the side of the bowl to prevent material from entering through the edges of the bowl and falling onto the rods when the material falls between the edge of the bowl and the edge, resulting in reduced cycle times.

Auto Stall - in cold weather conditions, the car will use the Auto Stall function to help heat up the gear oil faster, which will cause the car to switch from the torque converter drive (2nd gear) faster than on previous models.

Differential lock protection (standard) —This standard feature allows the machine to prevent the differential lock from being activated when damage may occur.

Improved cab - The interior of the K-Series cabins has improved the convenience and visibility of the operator by changing the dashboard design and key layout.

Car speed limit - this feature is used to select the top gear. If it is necessary to limit the maximum speed of the machine, the operator can select the maximum speed using the display or the maximum speed can be set to ET. This will allow the car to find the right gear that is best for the engine and transmission. Allowing the engine and transmission to choose the right gear to pull the load in most cases, resulting in a lower engine load factor and a reduction in the number of burned fuel verses using top gear selection, which required the machine to operate at engine speeds at high revs or close to by him.

 

Stroke speed control - Stroke speed control sets the operator the desired maximum speed if conditions on the working platform or segment speed limits require a speed that is less than full. The machine speed limit is intended for use when the maximum speed is to be limited for longer periods of time, and the travel speed control is for use when the maximum speed is to be reduced for shorter segments or intermediate periods of time. The operator can set the desired maximum speed, and the car will find the right gear, which is best suited for the engine and transmission. Allowing the engine and transmission to select the right gear to pull the load will in most cases reduce the engine load factor and reduce fuel consumption when choosing the top gear.

 

GENERAL

180° Curb-to-Curb Turning Width	38.71 ft
Elevator Flight Spacing	20.0 in
Fuel Tank Refill Capacity - Scraper	201.0 gal (US)
Maximum Depth of Cut	10.3 in
Maximum Depth of Spread	18.3 in
Maximum Floor Opening	4.4 ft
Number of Flights	15
Operating Weight - Empty	88061.0 lb
Overall Length	45.18 ft
Overall Shipping Height	12.37 ft
Overall Width	11.71 ft
Rated Load	25 038 kg (55,200 lb); 25.1 tonnes (27.6 tons)
Scraper Capacity - Heaped	23.0 yd³
Scraper Capacity - Struck	18.8 yd³
Tires - Scraper	33.25R29**E3
Tires - Tractor Drive	33.25R29**E3
Top Speed - Loaded	33.5 mile/h
Width - Cut	10.3 ft

ENGINE

Flywheel Power - Tractor/Scraper	304 kW (407 hp)
Engine Model	Cat C13 ACERT™
Flywheel Power - Tractor	407.0 HP
Note	C13 ACERT engine emits equivalent to U.S. EPA Tier 2/EU Stage II or U.S. EPA Tier 3/EU Stage III.
Rated Engine RPM	2000.0 r/min

TRANSMISSION

Top Speed - Loaded

33.5 mile/h

SCRAPER BOWL

Scraper Capacity - Heaped

23.0 yd³

SERVICE REFILL CAPACITIES

Fuel Tank	216.09 gal (US)
Crankcase	8.08 gal (US)
Cooling System	11.89 gal (US)
Hydraulic System	21.926 gal (US)
Transmission System	24.76 gal (US)

DIMENSIONS

Height - Overall Shipping	158.9 in
Length - Overall Machine	542.0 in
Width - Overall Machine	141.1 in
Height - Top of Cab	142.6 in
Height - Scraper Blade Maximum	20.5 in
Width - Tractor	133.1 in
Width - Inside of Bowl	120.0 in
Width - Outside Rear Tires	128.9 in
Front of Tractor to Front Axle	122.8 in
Wheel Base	329.5 in
Rear Axle - Rear of Machine	89.7 in
Ground Clearance - Tractor	21.9 in
Axle to Vertical Hitch Pin	17.0 in
Height - Top of Elevator	148.3 in
Width - Overall Machine - Ladder Down	149.2 in
Width - Rear Tire Centers	90.2 in

CAB

Exterior Sound Level	The exterior sound power level for the standard machine (ISO 6393) is 111.5 dB(A).
ROPS/FOPS	Meets ISO standards

SAFETY CRITERIA COMPLIANCE STANDARDS

Brakes	ISO 3450:2011
Falling Object Protective Structure (FOPS)	ISO 3449:2005 Level II
Reverse Alarm	ISO 9533:2010
Rollover Protection Structure (ROPS)	ISO 3471:2008 for up to 17 084 kg (37,664 lb)
Seat Belt	SAE J386:JUN1985
Steering System	ISO 5010:2007

TRAVEL SPEEDS - RUNOUT

Transmission Gear - Eighth	33.5 mile/h
Transmission Gear - Fifth	13.6 mile/h
Transmission Gear - First	3.1 mile/h
Transmission Gear - Fourth	10.1 mile/h
Transmission Gear - Reverse	5.7 mile/h
Transmission Gear - Second	5.5 mile/h
Transmission Gear - Seventh	24.8 mile/h
Transmission Gear - Sixth	18.4 mile/h
Transmission Gear - Third	7.5 mile/h

IMPLEMENT CYCLE TIMES

Bowl Lower	3.5 s
Bowl Raise	3.0 s
Ejector Extend	6.45 s
Ejector Retract	9.7 s

 

Dimensions

General

Overall Length 45.18ft in

Overall Width 11.71ft in

Specifications

Engine

Engine Model Cat C13 ACERT

Note

Cat C13 ACERT engine meets U.S. Environmental Protection Agency (EPA) Tier 4 Final/EU Stage IV engine emission standards.

Flywheel Power - Tractor/Scraper 304 kW (407 hp)

Rated Engine RPM 2000rpm

Flywheel Power – Tractr 407hp

Transmission

Top Speed – Loaded 33.5mph

Dimensions

Wheel Base 27.5ft in

Height - Top of Cab 11.9ft in

Length - Overall Machine 542in

Width - Outside Rear Tires 128.9in

Width - Inside of Bowl 120in

Height - Overall Shipping 158.9in

Width – Tractor 133.1in

Width - Overall Machine 141.1in

Ground Clearance – Tractor 21.9in

Front of Tractor to Front Axle 122.8in

Height - Scraper Blade Maximum 20.5in

Rear Axle - Rear of Machine 89.7in

Width - Overall Machine - Ladder Down 149.2in

Height - Top of Elevator 148.3in

Width - Rear Tire Centers 90.2in

Axle to Vertical Hitch Pin 17in

Service Refill Capacities

Cooling System 11.9gal

Fuel Tank 216.1gal

Crankcase 8.1gal

Hydraulic System 22gal

Diesel Exhaust Fluid 8.1gal

Transmission System 24.8gal

Cab

ROPS/FOPS Meets SAE and ISO standards

Exterior Sound Level

The exterior sound power level for the standard machine (ISO 6393) is 111.5 dB(A).

Scraper Bowl

Scraper Capacity – Heaped 23yd3

General

Tires - Tractor Drive 33.25R29**E3

Elevator Flight Spacing 20in

Number of Flights 15

Maximum Floor Opening 4.4ft in

Fuel Tank Refill Capacity – Scraper 201gal

Overall Width 11.8ft in

Overall Shipping Height 12.4ft in

Scraper Capacity – Struck 18.8yd3

Scraper Capacity – Heaped 23yd3

Rated Load 25 038 kg (55,200 lb); 25.1 tonnes (27.6 tons)

Width – Cut 10.3ft in

Maximum Depth of Cut 10.3in

Maximum Depth of Spread 18.3in

Top Speed – Loaded 33.5mph

180 degrees Curb-to-Curb Turning Width 38.8ft in

Tires – Scraper 33.25R29**E3

Operating Weight – Empty 88061lb

Overall Length 45.2ft in

Implement Cycle Times

Bowl Raise 3 s

Bowl Lower 3.5 s

Ejector Extend 6.45 s

Ejector Retract 9.7 s

Safety Criteria Compliance Standards

Rollover Protection Structure (ROPS) ISO 3471:2008 for up to 17 084 kg (37,664 lb)

Falling Object Protective Structure (FOPS) ISO 3449:2005 Level II

Brakes ISO 3450:1996

Steering System ISO 5010:2007

Seat Belt SAE J386:JUN1985

Reverse Alarm ISO 9533:2010

Travel Speeds – Runout

Transmission Gear – First 3.1mph

Transmission Gear – Second 5.5mph

Transmission Gear – Third 7.5mph

Transmission Gear – Fourth 10.1mph

Transmission Gear – Fifth 13.6mph

Transmission Gear – Sixth 18.4mph

Transmission Gear – Seventh 24.8mph

Transmission Gear – Eighth 33.5mph

Transmission Gear – Reverse 5.7mph