Caterpillar WHEEL LOADERS 914K - catalog of spare parts
Service replenishment options
Cooling system - 4.4 gal
Fuel tank - 39.6 gal
Engine crankcase - 3.4 gal
Transmission - Gearbox - 0.9gal
Hydraulic system - 22.5 gal
Hydraulic tank - refueling - 15.9 gal
Bridge - front, center - 2gal
Axis - front, each hub - 0.6gal
Bridge - rear, center - 2gal
Axis - rear, each hub - 0.6gal
3P1210 | CONE | Caterpillar | View |
7T9342 | CONE-BRG | Caterpillar | View |
6Y2736 | 6Y2736 | Caterpillar | View |
6Y2737 | CUP | Caterpillar | View |
7T9343 | CUP-BRG | Caterpillar | View |
Specifications
engine
Net power - 96hp
Peak Torque - 248 lbs
Torque increase - 17%
Displacement - 231.8 cubic meters.
Hole - 3.9 inches
4.7 inch stroke
Engine Model - Cat C3.8 Turbo
The note. The engine meets EPA Tier 4 Interim / EU Stage IIIB USA standards.
Maximum Gross Power - SAE J1995 - 97hp
Maximum Gross Power - ISO 14396 - 97 HP
Maximum gross power - 97 hp
Rated Net Power - SAE J1349 - 92 HP
Rated net power - ISO 9249 / EEC - 96 hp
Rpm at rated power - 400 rpm
Rated Torque - 237lb ft
Revolutions per minute with a maximum torque of 1500 rpm
Power train
Front axle - fixed
Rear Axle - Swing
Type (1) - The power transmission is fully hydrostatic, works with two engines in the gearbox system to increase torque.
Type (2) - the integrated coupling on one engine disengages at higher speeds to get maximum speed.
Front axle - Traction device - Differential lock
Rear Axle - Fluctuations - 11 degrees
Rear Axle - Traction Device - Differential Lock
Brakes - Service brakes - Internal wet disc
Brakes - Parking brake - Cable applied, spring release
Transmission
Type (2) - Creeper control allows you to adjust the maximum speed range from 0 to 10 km / h (6 mph) in speed range 1.
Type (1) - Switching from low range to high range occurs on the go for added convenience.
Ahead - low range, speed range 1 - 6.3 mph
Ahead - low range, speed range 2 - 12.5 mph
Ahead - High Range - 25 Mph
Reverse - Low Range, Speed Range 1 - 6.3 mph
Reverse - Low Range, Speed Range 2 - 12.5 mph
Reverse - High Range - 25 mph
Steering
Type of steering - The steering system uses a special double-acting double-acting pump.
Maximum Working Pressure - Steering Pump - 3,263 psi
Steering angle - in each direction - 40 degrees
Double Acting Steering Cylinder - Bore Diameter - 2.4 Inches
Double Acting Steering Cylinder - 1.4 Inch Diameter
Double-acting Steering Cylinder - Stroke - 15.7 inches
Maximum Steering Torque - 0 Degrees (Direct Machine) - 27,369 lb-ft
Maximum Steering Torque - 39 Degrees (Full Turn) - 21593 lb-ft
Steering cycle time - from stop to stop - at an engine speed of 2400 rpm, a steering wheel speed of 90 rpm - 2.8 s
The number of revolutions of the steering wheel - from stop to stop, wheel speed> 67 rpm - 3.75 revolutions
The number of revolutions of the steering wheel - from stop to stop, wheel speed <27 rpm - 5.75 revolutions
Maximum Flow - Steering Pump - 22.2 gallons / min
Weights
Operating Weight - 17,910 lbs.
Operating Weight - Standard Lift - 17,910 lbs.
Operating Weight - High Lift - 18030 lbs
Tires
NOTE Wheel sets are interchangeable between 910K and 914K.
Tire Size - Standard - 17.5-25 12PR
Tire size - optional (1) - 17.5-R25
Tire size - option (2) - 17.5-25 16PR
Tire size - non-pneumatic - Flexport - 53.5916.5 (equivalent to 15.5 / 17.525)
Buckets
Bucket volume - 1.2 m3-2.5 m3 (1.6 s3-3.3 s3)
General purpose - 1.2-1.5 m3 (1.6-2.0 cubic meters)
Bucket type
Performance Series buckets use a long floor and open throat for easy loading and good material retention.
Performance characteristics
Nominal bucket capacity - 3.3yd3
Ground clearance - 45 degree full lift and unload - 112 ft.
Departure - 45 degrees, full rise and discharge - 31 feet to
Joint angle - in each direction - 40 degrees
Full Tip Loading - 12,294 lbs
Full Turn Tipping Load - Standard Lift - 10,538 lbs
Tipping Load per Turn - High Lift - 8603 lbs
Taxi
ROPS - ROPS: SAE J1040 MAY94, ISO 3471-1994.
Fops - FOPS: SAE J / ISO 3449 APR98, Level II, ISO 3449 1992, Level II.
Sound
The declared dynamic sound pressure level of the operator in accordance with ISO 6396: 2008 is: - Deluxe Cabin: 75 dB (A)
Loader hydraulic system
Maximum Working Pressure - Implement Pump - 3,046 psi
Primary Discharge Pressure - 4061 psi
Maximum Pump Flow 33 Gallons / Min
Maximum Consumption - Implement Pump - 3rd Function - 25 gal / min
Maximum Consumption - Implement Pump - 4th Function - 25 gal / min
Cycle Time - Rise - 5.3 s
Cycle Time - Dump - 1.8 s
Cycle Time - Rackback - 2.4 s
Cycle Time - Float - 3.7 s
Cycle time - lower, float - 4 s
Lift Cylinder - 3.9 Inch Bore
Lifting Cylinder - Rod Diameter - 2.4 Inches
Lifting Cylinders - Stroke - 23.3 inches
Tilt Cylinder - 3.9 Inch Hole Diameter
Tilt Cylinder - Stem Diameter - 2.4 Inches
Tilt Cylinder - Stroke - 22.8 inches