Caterpillar WHEEL LOADERS 910K - catalog of spare parts
Power train
Front axle - fixed
Rear Axle - Swing
Type (1) - The power train is fully hydrostatic, works with two motors in the gearbox system to enhance torque.
Type (2) - the built-in coupling on one engine disengages at higher speeds to get the maximum speed.
Front axle - Traction device - Differential lock
Rear Axle - Fluctuations - 11 degrees
Rear Axle - Traction Device - Differential Lock
Brakes - Service brakes - Internal wet disc
Brakes - Parking brake - Cable applied, spring release
| 2S0480 | CUP | Caterpillar | View |
| 7T9342 | CONE-BRG | Caterpillar | View |
| 6Y2736 | 6Y2736 | Caterpillar | View |
| 6Y2737 | CUP | Caterpillar | View |
| 7T9343 | CUP-BRG | Caterpillar | View |
Specifications
engine
Net power - 93 hp
Peak Torque - 248 lbs
Torque boost - 17%
Displacement - 231.8 cc
Hole - 3.9 inches
4.7 inch travel
Engine Model - Cat C3.8 Turbo
Maximum Gross Power - SAE J1995 - 97hp
Maximum Gross Power - ISO 14396 - 97 HP
Maximum gross power - 97 hp
Rated Net Power - SAE J1349 - 92 HP
Rated net power - ISO 9249 / EEC - 93 hp
Rpm at rated power - 2400 rpm
Rated Torque - 237lb ft
Rpm at peak torque of 1,500 rpm
Transmission
Type (2)
Creeper control provides maximum speed range adjustment from 0 to 10 km / h (6 mph) in speed range 1.
Type (1)
Switching from low range to high range occurs on the go for added convenience.
Ahead - Low Range, Speed Range 1 - 6.3 mph
Ahead - Low Range, Speed Range 2 - 12.5 mph
Ahead - High Range - 25 mph
Reverse - Low Range, Speed Range 1 - 6.3 mph
Reverse - Low Range, Speed Range 2 - 12.5 mph
Reverse - High Range - 25 mph
Steering
Steering Type - The steering system uses a special double-acting double-cylinder pump.
Maximum Operating Pressure - Steering Pump - 2,683 psi
Steering joint angle - in each direction - 40 degrees
Double Acting Steering Cylinder - Bore Diameter - 2.4 Inches
Double Acting Steering Cylinder - 1.4 Inch Diameter
Steering Cylinder, Double-acting - Stroke - 15.7 inches
Maximum Steering Torque - 0 Degrees (Direct Machine) - 21,993 lb-ft
Maximum Steering Torque - 39 Degrees (Full Turn) - 17,351 lb-ft
Steering cycle time - from stop to stop - at an engine speed of 2400 rpm, steering wheel speed of 90 rpm - 3.2 s
The number of revolutions of the steering wheel - from stop to stop, wheel speed> 67 rpm - 3.75 revolutions
The number of revolutions of the steering wheel - from stop to stop, wheel speed <27 rpm - 5.75 revolutions
Maximum Flow - Steering Pump - 15.9 gallons / min
Weights
Working Weight - 15,714 lbs.
Working Weight - Standard Lift - 15,714 lbs
Working Weight - High Lifting Height - 16837 Pounds
Tires
Note. Wheel pairs are interchangeable between 910K and 914K.
Tire Size - Standard - 15.5-25 12PR
Tire Size - Option (3) - 15.5-R25
Tire size - option (1) - 16.9-24 10PR
Tire size - option (2) - 16.9-24 12PR
Tire size - Non-pneumatic - Flexport - 53.5916.5 (equivalent to 15.5 / 17.525)
Buckets
Bucket capacity - 1.2 m3-2.5 m3 (1.6 s3-3.3 s3)
General purpose - 1.2-1.5 m3 (1.6-2.0 m3)
Bucket Type
Performance Series buckets use a long floor and open throat for easy loading and good material retention.
Performance characteristics
Nominal bucket capacity - 3.3yd3
Ground Clearance - Full Elevator and 45 Degree Dump - 112 Feet in
Achieve - Full climb and 45 degree dump - 29 ft.
Steering joint angle - in each direction - 40 degrees
Full Tip Load - 9,958 lbs
Full Turn Tipping Load - Standard Lift - 9,460 pounds
Full Turn Tipping Load - High Rise - 8844 lbs
Service replenishment options
Cooling system - 4.4 gal
Fuel tank - 39.6 gal
Engine crankcase - 3.4 gal
Transmission - Gearbox - 0.9gal
Hydraulic system - 22.5 gal
Hydraulic Tank - Refill - 15.9 gallons
Bridge - front, center - 2gal
Axis - front, each hub - 0.6gal
Bridge - rear, center - 2gal
Axis - rear, each hub - 0.6gal
Taxi
ROPS - ROPS: SAE J1040 MAY94, ISO 3471-1994.
FOPS - FOPS: SAE J / ISO 3449 APR98, Level II, ISO 3449 1992 Level II.
Sound
The declared dynamic sound pressure level of the operator according to ISO 6396: 2008 is: - Deluxe Cabin: 75 dB (A)
Loader hydraulic system
Maximum Working Pressure - Implement Pump - 3,046 psi
The main pressure relief - 3568 pounds per square inch
Maximum pump flow rate - 26 gal / min
Maximum Consumption - Implement Pump - 3rd Function - 25 gal / min
Maximum Consumption - Implement Pump - 4th Function - 25 gal / min
Cycle Time - Rise - 5.9 s
Cycle time - dump - 2 s
Cycle Time - Rackback - 3 s
Cycle Time - Float - 4.1 s
Cycle time - lower, float - 4.4 s
Lift Cylinder - 3.9 Inch Bore
Lifting Cylinder - Rod Diameter - 2.4 Inches
Lifting Cylinders - Stroke - 23.3 inches
Tilt Cylinder - 3.9 Inch Hole Diameter
Tilt Cylinder - Stem Diameter - 2.4 Inches
Tilt Cylinder - Stroke - 22.8 inches