Caterpillar WHEEL LOADERS 908 - catalog of spare parts
Bucket
Discharge clearance at maximum lift - 10.33 feet per
Dimensions
Length with a bucket on the ground - 17.43 feet in
Tire Width - 6.42 Feet
Height to Cab Top - 9.08 ft in
Wheelbase - 7.25 feet in
Articulated finger - maximum height - 11.08 feet in
Weights
Working Weight - 13,288 lbs
Choose WHEEL LOADERS 908 section:
| 2S0480 | CUP | Caterpillar | View |
| 2P8104 | 2P8104 | Caterpillar | View |
| 7T6088 | BEARING A | Caterpillar | View |
| 7T8419 | BEARING | Caterpillar | View |
| 7T9344 | CONE | Caterpillar | View |
| 7T9345 | CUP | Caterpillar | View |
| 3T4308 | BEARING | Caterpillar | View |
Specifications
engine
Net power - 76l.s.
Gross Power - 84 HP
ISO 9249 Rating - 80 HP
EEC 80/1269 Rating - 80hp
SAE J1349 Rating - 80hp
Operational
Working Weight - 13,288 lbs
Fuel capacity - 21 gal
Hydraulic system capacity - 17 gal
Engine oil volume - 2.6gal
5.8 gallon cooling capacity
Transmission fluid capacity - 2.6gal
Static Tipping Weight - 9636 lbs
Operating voltage - 12 V
The amplifier from the generator - 90 amperes
Rear Axle Fluctuation - 22 degrees
Tire size - 12.5-18
Transmission
Transmission Type - Hydrostatic
The number of forward gears - 2
Number of reverse gears - 2
Top Speed - Forward - 12 Mph
Max. Speed - Reverse - 12 mph
Buckets
Bucket Width - 6.9 Feet in
Hydraulic System - Pump Type
Gearbox - Installing a safety valve - 3400
Pump productivity - 15.9 gal / min
Lifting Time - 4.5sec
Dump time - 2.4 sec.
Shorter time - 3.2 s
Hydraulic Cycle Time - Dump - 2.4
Hydraulic Cycle Time - Lift - 4.5
The main relief is 3,400 psi
Hydraulic cycle time - lower, float - 3.2
3rd valve flow rate - 21.6 gallons / min
Flow pressure at 2600 rpm and 70 bar (1000 psi) - 15.9 gallons per minute
Bucket
Breakout Force - 13,710 pounds
Discharge clearance at maximum lift - 10.4 feet per
Bucket Width - 6.8 Feet in
Bucket Capacity - Bulk - 0.8yd3
Dimensions
Length with bucket on the ground - 17.5 feet in
Tire Width - 6.5 Feet in
Height to Cab Top - 9.1 ft.
Wheelbase - 7.3 feet in
Articulated Finger - Maximum Height - 11.1 Feet
Tread Width - 62.4 inches
Performance characteristics
Breakout Force - 13,710 pounds
Nominal bucket capacity - 1.3yd3
Blade height at full lift - 10.4 feet in
Articulation - 40 degrees
Fluctuation +/- 11 degrees
Full Turn Static Tipping Load - Bucket - 8270 lbs
Stand back - transport position - 56 degrees
Rated Full Load Turnover Load - Bucket - 4,136 pounds
Hydraulic Lift Payload - 9,900 lbs
Direct Tipping Load - Bucket - 9,636 lbs.
Reach - Without Teeth - 2.8 Feet
Rated Full Load Turnover - Fork - 5291 lbs
Full Turn Static Tipping Load - Fork - 6,860 pounds
Service replenishment options
Cooling system - 5.8 gal
Fuel tank - 21 gal
Hydraulic system - 17 gal
Engine oil - 2.6gal
Taxi
ROPS - Meets the following criteria: SAE J1040 MAY94, ISO 3471-1: 1986
FOPS - Meets the following criteria: SAE J231 JAN81, ISO 3449: 1992
Sound
Sound level below 75 dB (A) - maximum material density
General Purpose Bucket - 0.6 m3 (0.8 yards3) - 3760 lbs / yard
Multipurpose Bucket - 0.6 m3 (0.8 yards3) - 3300 lbs / yard
Lightweight material - bucket 1.0 m3 (1.3 yards3) - 1675 lbs / yard
Side Dump Bucket - 3105 lbs / yard
High Dump Bucket - 0.7 m3 (0.8 yards3) - 3230 lbs / yard
Stone Screen Bucket - 0.6 m3 (0.8 yards) - 3380 lbs / yard
Motor dimensions
Hole Diameter - 3.7 inches
4.8 inches
Powertrain, axles and brakes
Transmission type - two-stage hydrostatic single-pass transmission with a closed loop.
Maximum speeds - with tires 12.5-18, forward and backward, low - 4 mph
Top speed - forward and reverse, high - 12 miles per hour
Axle and final drives - fixed front axle with limited slip differential and planetary gear
Service and parking brake - combined into one, dry brake drive brake
Brake Standards - The brake complies with ISO 3450: 1996