Caterpillar WHEEL LOADERS 906H2 - catalog of spare parts
Dimensions
Digging Depth - 3.5 inches
Length with bucket on the ground - 18.4 feet in
Ground clearance - 1 foot in
Wheelbase - 7.2 Feet
Articulated finger - maximum height - 10.6 feet per
Reach in Max Lift and Dump - 4.2 feet in
Cabin Height - 8.1 Feet in
Wheelbase - 7.2 Feet
Maximum reach - 4.2 feet per
Maximum Blade Height - 7.9 Feet in
Total length - with bucket - 18.4 feet in
Departure angle - degrees - 34 degrees
Fork Height at Maximum Departure - 4.9 Feet
Turn Radius - Inner Tire - 7.4 ft.
Width - Bucket - 6.2 Feet in
Tire measure - 4.7 feet in
Machine Width - 6 Feet in
Departure at maximum blade height - 2.7 feet
10 ft. In height
Hinge pin at maximum height - 10.6 feet per
Total length - with forks - 19.5 feet in
Reach at ground level - 2.5 feet in
Fork Depth Above Ground - 1.8 Inches
Maximum Fork Height - 10.4 Feet in
Departure pitchfork at maximum height - 1.7 feet in
Turn radius - above bucket - 14.6 feet per
Joint angle - degrees - 39 degrees
Dump angle at maximum height - degrees - 45 degrees
Choose WHEEL LOADERS 906H2 section:
| 1T0994 | BEARING-BALL | Caterpillar | View |
| 2S0480 | CUP | Caterpillar | View |
| 6Y6846 | 6Y6846 | Caterpillar | View |
Specifications
engine
Engine make - 2236
Engine Model - C3.3B DIT
Net power - 69hp
Gross Power - 74 HP
Hole - 3.7 inches
4.7 inch travel
Maximum apparent power - SAE J1995 - 74 hp
Maximum net power - SAE J1349 - 68 hp
Maximum apparent power - ISO 14396 - 73 hp
Rated net power - 2500 rpm - SAE J1349 - 68 hp
Maximum net power - ISO 9249 - 69 hp
Gross Power - 2500 rpm - SAE J1995 - 74 hp
Net power - 2500 rpm - SAE J1349 - 68 hp
Operational
Operating Weight - 4,553 lbs
Fuel Capacity - 13.7 Gallons
Hydraulic Capacity 25 Gallons
2.7 gallon engine oil
Cooling system capacity - 6.3 gal
Transmission
Number of forward gears - 3
Top Speed - Forward - 21.7 Mph
Speed 1 - 4.3 miles per hour
Speed 2 - 12.4 mph
High Speed - 21.7 mph
Weights
Working Weight - 12,412 lbs.
Buckets
Bucket volume - 0.75-1.2 m3 (0.98-1.6 m3)
Hydraulic system
Pump Type - Piston
Safety Valve Installation - 3400
Pump capacity - 22 gal / min
Raising time - 5sec
Dump Time - 2sec
Drop Time - 4sec
Hydraulic cycle time - dump - 2 seconds
Hydraulic Cycle Time - Lift - 5 Seconds
Hydraulic Cycle Time - Rackback - 2.5 seconds
The main relief is 3,400 psi
Hydraulic cycle time - lower, float - 4 seconds
3rd auxiliary stream - standard stream - 22 gallons / min
3rd Auxiliary Flow - High Flow - 33 gallons / min
Performance characteristics
Tear Off - 9,442 lbs
Nominal bucket capacity - 1.2yd3
Tire size - 405/70 R18
Full Turn Static Tipping Load - Bucket - 6,967 lbs.
Stand back - transport position - 52 degrees
Rated Full Load Turnover Load - Bucket - 3,483 lbs.
7194 lb hydraulic lift capacity
Direct Tipping Load - Bucket - 8785 lbs
Nominal full-load workload - forks (EN 474-3: 2006, firm and flat surface, 500 mm (20 in) load center, 100 mm (4 in) transport above ground) - 5,997 pounds
Nominal full-load workload - forks (EN 474-3: 2006, firm and flat surface, 1.25 stability, and 500 mm [20 in] load center) - 4,553 lbs.
Nominal full-load workload - forks (SAE J1197, mid-point load center, 1120 mm [44 in) teeth) (50% FTSTL) - 2652 lbs
Nominal full-load workload - forks (SAE J1197, mid-point load center, 1220 mm [48 in] teeth) (50% FTSTL) - 2544 lbs.
Nominal Working Load, Straight Rear - Forks (SAE J1197, Center of Load at Mid-Tooth, 1120 mm [44 in.)) (50% FTSTL) - 3,476 pounds
Nominal Working Load, Straight Rear - Forks (SAE J1197, Mid-Point Load Center, 1220 mm [48 in] Teeth) (50% FTSTL) - 3404 lbs.
Nominal full-load workload - forks (EN 474-3: 2006, hard and flat surface, 500 mm [20 in] load center) (80% of FTSTL) - 4,553 lbs.
Nominal full-load workload - forks (EN 474-3: 2006, hard and flat surface, 500 mm [20 in] center of load) (60% of FTSTL) - 3,415 pounds
Service replenishment options
Cooling system - 6.3 gal
Fuel tank - 13.7 gal
Hydraulic system - 25gal
Engine oil - 2.6gal
Taxi
ROPS - SAE J1040 MAY94, ISO 3471-1994
FOPS - SAE J / ISO 3449 APR98 Level II, ISO 3449 1992 Level II
Maximum Material Density - General Purpose
Nominal Capacity - 1.2yd3
Blade Height 94 Inches
Maximum Material Density - 2958 lbs / yard
Bucket Width - 74 inches
Maximum Material Density - Lightweight Material
Nominal Capacity - 1.6yd3
Blade height 90 inches
Maximum Material Density - 2036 lbs / yard
Bucket Width - 82 inches
Maximum Material Density - Multipurpose
Rated Power - 1yd3
Blade height - 97 inches
Maximum Material Density - 3592 lbs / yard
Bucket Width - 74 inches
Operator Environment Features - Canopy
Fixed steering column - standard
Vinyl Suspension Seat - Standard
Hook - Standard
Sun Visor - Standard
Exterior Mirrors (2) - Knock Back - Standard
Lockable Storage Box - Standard
Adjustable Interior Mirror - Standard
Operator Environment Features - Comfort Cab
Two Access Doors - Standard
Adjustable Steering Column - Standard
Suspension seat, armrest - standard
Left Window - Sliding - Standard
Rear window defroster - standard
Hook - Standard
Cabin Light - Standard
Sun Visor - Standard
Radio kit (wiring, speaker, antenna and grilles) - standard
Exterior Mirrors (2) - Knock Back - Standard
Heater - Standard
Lockable Storage Box - Standard
Adjustable Interior Mirror - Standard
Rear Curtain - Optional
Radio Cat / CD / MP3 / WMA Player - optional
Operator Environment Features - Deluxe Cab
Two Access Doors - Standard
Rear window defroster - standard
Hook - Standard
Cabin Light - Standard
Adjustable Steering Column - Standard
Air-conditioned fabric seat, armrest, lumbar support, rear heated seat - standard
Left Window - Sliding - Standard
Right Window - Sliding - Standard
Air Conditioner - Standard
Rear Curtain - Optional
Radio Cat / CD / MP3 / WMA Player - optional
Sun Visor - Standard
Radio kit (wiring, speaker, antenna and grilles) - standard
Exterior Mirrors (2) - Knock Back - Standard
Heater - Standard
Lockable Storage Box - Standard
Adjustable Interior Mirror - Standard