Caterpillar WHEEL LOADERS 906 - catalog of spare parts

 

Specifications

engine

Engine make - 2236

Engine Model - 3044C

Net power - 68hp

Gross Power - 75 HP

Measured Power @ - 2600 rpm

ISO 9249 Rating - 71 HP

EEC 80/1269 Rating - 71h.p.

SAE J1349 Rating - 71h.p.

 

Operational

Working Weight - 10912 lbs

The capacity of the fuel tank is 19.6 gal

Hydraulic Capacity 17.5 Gallons

Engine oil volume - 2.6gal

Cooling system capacity - 5.5gal

Transmission fluid capacity - 2.6gal

Static Tipping Weight - 7546 lbs

Operating voltage - 12 V

The amplifier from the generator - 90 amperes

Rear Axle Fluctuation - 22 degrees

Tire size - 12.5x18

 

Transmission

Transmission Type - Hydrostatic

The number of forward gears - 2

Number of reverse gears - 2

Top Speed ​​- Forward - 12 Mph

Max. Speed ​​- Reverse - 12 mph

 

Weights

Working Weight - 10912 lbs

 

Buckets

Bucket Width - 6.2 Feet in

 

Hydraulic system

Pump Type - Gear

Installation of a safety valve - 3408.4

Pump productivity - 18 gal / min

Lifting Time - 4.5sec

Dump time - 1.5 sec.

Shorter time - 3.2 s

Hydraulic Cycle Time - Dump - 1.5

Hydraulic Cycle Time - Lift - 4.5

The main relief is 3,400 psi

Hydraulic cycle time - lower, float - 3.2

3rd valve flow rate - 17.7 gal / min

Flow pressure at 2600 rpm and 70 bar (1000 psi) - 15.9 gallons per minute

 

Bucket

Breakout Force - 10,340 pounds

Unloading at Maximum Lift - 8 ft.

Bucket Width - 6.2 Feet in

Bucket Capacity - Bulk - 0.8yd3

 

Dimensions

Length with bucket on the ground - 16.6 feet in

Tire Width - 6.2 Feet in

Height to Cab Top - 8.8 Feet in

Wheelbase - 6.5 feet in

Articulated Finger - Maximum Height - 10.3 Feet

Reach in Max Lift and Dump - 2.6 feet in

Tread Width - 55 Inches

 

Performance characteristics

Breakout Force - 10,340 pounds

Nominal bucket capacity - 1.1yd3

Blade height at full lift - 8 ft.

Articulation - 40 degrees

Fluctuation +/- 11 degrees

Full Turn Static Tipping Load - Bucket - 6,666 lbs.

Stand back - transport position - 53 degrees

Rated Full Load Turnover Load - Bucket - 3,333 lbs.

9,100 lbs hydraulic lift capacity

Direct Tipping Load - Bucket - 7,546 pounds

Reach - Without Teeth - 2.8 Feet

Rated Full Load Turnover - Fork - 4,433 lbs

Full Turn Static Tipping Load - Fork - 5,500 pounds

 

Service replenishment options

Cooling system - 5.5gal

Fuel tank - 19.6 gal

Hydraulic system - 17.5 gal

Engine oil - 2.6gal

 

Taxi

ROPS - Meets the following criteria: SAE J1040 MAY94, ISO 3471-1: 1986

FOPS - Meets the following criteria: SAE J231 JAN81, ISO 3449: 1992

Sound - sound level below 75 dB (A)

 

Maximum material density

General Purpose Bucket - 0.6 m3 (0.8 yards3) - 3000 lbs / yard

Multipurpose Bucket - 0.6 m3 (0.8 yards3) - 3000 lbs / yard

Lightweight - 1.0 m3 (1.3 yards3) bucket - 1950 lbs / yard

Side Dump Bucket - 3000 lbs / yard

High Dump Bucket - 0.7 m3 (0.8 cubic feet) - 3200 lbs / sq.

Stone Screen Bucket - 0.6 m3 (0.8 yards) - 3300 lbs / yard

 

Motor dimensions

Hole - 3.7 inches

 

Powertrain, axles and brakes

Transmission type - two-stage hydrostatic single-pass transmission with a closed loop.

Maximum speeds - with tires 12.5-18, forward and backward, low - 4 mph

Top speed - forward and reverse, high - 12 miles per hour

Axle and final drives - fixed front axle with limited slip differential and planetary gear

Service and parking brake - combined into one, dry brake drive brake

Brake Standards - The brake complies with ISO 3450: 1996