Caterpillar SKID STEER LOADER 242D - catalog of spare parts
Dimensions
Ground clearance - 0.8 feet in
Wheelbase - 3.7 ft. In
Bucket Pin Height - Maximum Lifting Height - 10.1 Feet
Height - Cab Top - 7 ft.
Length - Without Bucket - 108.9 Inches
Length - with bucket on the ground - 137.3 inches
Maximum total height - 154.2 inches
Bucket Finger Height - Carry Position - 7.9 Inches
Clearance at maximum lift and unload - 90 inches
Departure angle - 27 degrees
Maximum angle of dumping - 52 degrees
Rear Upright Angle - Maximum Height - 87 degrees
Pin Bucket Lug - Maximum Lifting - 7.2 Inches
Achieve - Maximum Rise / Drop - 21.7 inches
Turning radius from center - rear of car - 64.5 inches
Center Turn Radius - Clutch - 51.8in
Maximum reach - with arms parallel to the ground - 49.2 inches
Center Turn Radius - Bucket - 83 inches
Width of the car over tires - 66 inches
Bumper protrusion - behind the rear axle - 40.2 inches
Choose SKID STEER LOADER 242D section:
Specifications
engine
Displacement - 203cu per
Hole Diameter - 3.7 inches
4.7 inch travel
Net Power - ISO 9249 - 73.9 HP
Gross Power - SAE J1995 - 74.3 HP
Engine Model - Cat C3.3B DIT (Turbo)
Net Power - SAE 1349 - 73.2 HP
Peak Torque - 1,500 rpm - SAE J1995 - 195 lb-ft
Flywheel net power - 73.2 hp
Power train
Travel Speed - Forward or Reverse - One Speed - 7.5 Miles per Hour
Travel Speed - Forward or Reverse - Two Speed - 11.5 mph
Weights
Operating Weight - 6,980 pounds
The note
Operating Weight, Performance and Dimensions, All Based on an Operator Weighting 75 kg (165 lbs), All Fluids, One Speed, OROPS, 1676 mm (66 inches) Trash Can, Cat 12 16.5 Tires, Standard Hydraulic Flow System, Seat with mechanical suspension, optionally no counterweights and manual quick couplings (unless otherwise indicated).
Hydraulic system
Hydraulic Flow - Standard - Loader Hydraulic Pressure - 3335 psi
Hydraulic flow - Standard - Loader hydraulic flow - 20 gal / min
Hydraulic flow - Standard - Hydraulic power (rated) - 39 hp
Hydraulic flow - high flow rate - hydraulic power (calculated) - 58 hp
Hydraulic Flow - High Flow - Maximum Loader Hydraulic Pressure - 3335 psi
Hydraulic flow - high flow rate - maximum hydraulic flow of the loader - 30 gal / min
Operational characteristics
The note
Operating Weight, Performance and Dimensions, All Based on an Operator Weighting 75 kg (165 lbs), All Fluids, One Speed, OROPS, 1676 mm (66 inches) Trash Can, Cat 12 16.5 Tires, Standard Hydraulic Flow System, Seat with mechanical suspension, optionally no counterweights and manual quick couplings (unless otherwise indicated).
Nominal Working Capacity with Extra Counterweight - 2,350 lbs
Tipping Load - 4,300 pounds
Breakout Force - Tilt Cylinder - 5034 lbs.
Nominal Capacity 2150 lbs
Service replenishment options
Cooling System - 3.7gal
Fuel tank - 27.7 gal
Hydraulic Tank - 10.3 Gallons
Crankcase - 3gal
Hydraulic system - 13.2 gal
Chain box - each side - 2.3 gal
Taxi
ROPS - ISO 3471: 2008
FOPS - ISO 3449: 2005 Level I
FOPS Level II - ISO 3449: 2005 Level II
Air conditioning system
Air conditioning
The air conditioning system on this unit contains the fluorinated greenhouse refrigerant R134a (global warming potential = 1430). The system contains 0.81 kg of refrigerant with a CO2 equivalent of 1.158 metric tons.
Noise level
Note (1)
Cab and Roll Over Protective Structures (ROPS) are standard in North America and Europe.
Note (2)
** Declared dynamic sound pressure levels of the operator according to ISO 6396: 2008. The measurements were carried out with the doors and windows of the cabin closed and at 70% of the maximum engine cooling fan rotation speed. Sound levels may vary at different speeds of the engine cooling fan.
Note (3)
*** The indicated sound power level for marked CE configurations when measured in accordance with the test procedure and conditions specified in 2000/14 / EC.
Inside the cab ** - 83 dB (A)
External cab *** - 101 dB (A)