Your region: United States

Caterpillar MOTOR GRADER 140M 3 AWD - catalog of spare parts

Tandems

Growth - 19.9in

width - 7.9in

Sidewall Thickness - Inner - 0.7in

Sidewall Thickness - Outer - 0.8in

Drive chain pitch - 2in

Wheel axle spacing - 60in

Tandem Swing - Forward-Up - 15 degrees

Tandem Swing - Front to Down - 25 degrees

Weights - AWD

Gross Vehicle Weight - Base - Front Axle - 10726lb

Gross Vehicle Weight - Base - Rear Axle - 29654lb

Total vehicle weight - basic - total - 40380lb

Gross Vehicle Weight - Maximum - Front Axle - 17075lb

Gross Vehicle Weight - Maximum - Rear Axle - 38069lb

Gross Vehicle Weight - Maximum - Total - 55144lb

Weight in working order - usually equipped - front axle - 13601lb

Operating Weight - Typically Rear Axle - 32316lb

Weight in working condition - usually included - total - 45917lb

Choose MOTOR GRADER 140M 3 AWD section:

1084086 Kit Follower Caterpillar View
0966166 Washer Hard Caterpillar View
1615967 Shaft Caterpillar View
1163715 Studs Taper Lock Caterpillar View
1412760 Fuse Caterpillar View
3808418 Bolt Flange Caterpillar View
3483426 Bolt12 Point Head Caterpillar View
1148845 Sleeve Plastic Caterpillar View
4V8577 Bearing Caterpillar View
1268440 Seal ORing Caterpillar View
1889637 Plate Retraction Caterpillar View
3446590 Coil As Caterpillar View
1938308 Adapter Caterpillar View
2K0703 Bar Caterpillar View
5P4423 Elbow Caterpillar View
1631137 Bearing Caterpillar View
2407879 Plug As Connector Caterpillar View
1361543 Plate As Lumbar Caterpillar View
5P7648 Grommet Caterpillar View
3650162 Connector Sp Caterpillar View
1P3702 Rectangular Seal Caterpillar View
1013055 Cover Speaker Caterpillar View
8Y6860 Kit Spring Caterpillar View
1219917 Washer Caterpillar View
2397352 Plug As Connector Caterpillar View
3915262 Gasket Caterpillar View
1028803 Kit Receptacle Caterpillar View
0619455 Oring Caterpillar View
1233827 Bulk Seal Caterpillar View
3984747 Pump Gp Def Caterpillar View
2967724 Coil Gp Ignition Caterpillar View
1051646 Piston As Pump Caterpillar View
6K0545 Hex Head Self Locking Nuts Caterpillar View
8U9480 Pin Caterpillar View
5C2537 Bolt Caterpillar View
1728039 Terminal Caterpillar View
1471446 Plug As Connector Caterpillar View
2388245 Plug As Connector Caterpillar View
8T8137 Seal Face Caterpillar View
7T9302 Knob As Wiper Switch Caterpillar View
3413150 Cat aftermarket Hydraulic Connector Caterpillar View
1927805 Harness As Valve Caterpillar View
8C8842 Hex Head Bolts, Zinc Plated Caterpillar View
3584889 Ether Start Filter Caterpillar View
1W5455 VBand Clamp Caterpillar View
5P8525 Grommet Caterpillar View
2492844 Washer Caterpillar View
6V5853 Blade As Wiper Caterpillar View
8S2634 Cover As Caterpillar View
7Y3283 Spacer Caterpillar View
3851173 Sensor Gp Pr Caterpillar View
5P7657 Seal Caterpillar View
5C7423 Machine Screws Flat Head Caterpillar View
1108769 Wire As Caterpillar View
3445673 , Hex Nuts, Zinc Flake Caterpillar View
1336517 Cap As Dust Caterpillar View
1747875 Horn As Caterpillar View
1053477 Bolt Socket Head Caterpillar View
7E3443 Bushing Terminal Caterpillar View
7N9943 Miniature Electrical Lamps Caterpillar View

Specifications

Ripper

Breakout Power - 27,794 lbs

Digging Depth - Maximum - 16.8 inches

Shank Holders - 5

Penetration Power - 20,812 pounds

Increase in machine length, beam increase - 40.6 inches

Distance between ripper shank holders - 21 inches

Engine

The number of cylinders - 6

Torque boost - 39%

Displacement - 567.5 cubic meters.

Hole Diameter - 4.5 Inches

Stroke - 5.9 inches

Emissions - USA, EPA Tier 4 Final / EU Stage IV

Engine Model - Cat C9.3 ACERT

Altitude reduction of 10,000 feet in

Base power (1st gear) - net - 200 hp

Standard feature - 109 degrees

Speed ​​at rated power - 2000 rpm

High - Environmental Capability - 122 degrees

All Wheel Drive Range - Net - 156-203 kW (210-272 HP)

Base power (1st gear) - net - metric - 202 hp

All-wheel drive range - Net - Metric - 156-203 kW (213-276 HP)

Maximum Torque - All Wheel Drive - 1,000 lb ft

High Ambient - Fan Speed ​​- Maximum - 1550 rpm

VHP Plus - Transmission - Net Power - Forward 8th - 252 HP

VHP Plus - Transmission - Net Power - Reverse - 200 HP

VHP Plus - Gearbox - Net power - Reverse 2 - 210hp

VHP Plus - Transmission - Net Power - Reverse 3-6 - 220 HP

AWD Off: transmission - net power - forward - 1st - 210hp

AWD Off: transmission - net power - forward - 2nd - 220hp

AWD Off: Transmission - Net Power - Forward - 3rd - 231 HP

AWD Off: Transmission - Net Power - Forward - 4th - 236 HP

AWD Off: Transmission - Net Power - Forward - 5th - 241 HP

AWD Off: Transmission - Net Power - Forward - 6th - 247 HP

AWD Off: transmission - net power - forward - 7th - 252 hp

AWD Off: Gear - net power - forward - 8th - 252 hp

AWD Off: Transmission - Net Power - Reverse - 1st - 200 HP

AWD Off: transmission - net power - reverse - 2nd - 210hp

AWD Off: transmission - net power - reverse - 3-6, 220 hp

AWD On: transmission - net power - forward - 1st - 220 hp

AWD On: transmission - net power - forward - 2nd - 241 hp

AWD On: Transmission - Net Power - Forward - 3rd - 247 HP

AWD On: transmission - net power - forward - 4th - 252 hp

AWD On: transmission - net power - forward - 5 - 272 hp

AWD On: Gear - net power - forward - 6th - 272 hp

AWD On: transmission - net power - forward - 7th - 272 hp

AWD On: Gear - net power - forward - 8 - 272 hp

AWD On: transmission - net power - reverse - 1st - 200 hp

AWD On: transmission - net power - reverse - 2nd - 210hp

AWD On: transmission - net power - reverse - 3-6, 220 hp

High ambient temperature - fan speed - standard - 1400 rpm

Maximum Torque - VHP Plus - 920 lb ft

High Ambient - Fan Speed ​​- Minimum - 500 rpm

VHP Plus Range - Net - 149-188 kW (200-252 HP)

VHP Plus Range - Net - Metric - 149-188 kW (202-255 HP)

VHP Plus - Transmission - Net Power - Forward 1 - 200hp

VHP Plus - Transmission - Net Power - Forward 2 - 210hp

VHP Plus - Transmission - Net Power - Forward 3rd - 220hp

VHP Plus - Transmission - Net Power - Forward 4th - 231 HP

VHP Plus - Transmission - Net Power - Forward 5 - 236hp

VHP Plus - Transmission - Net Power - Forward 6 - 241 HP

VHP Plus - Transmission - Net Power - Forward 7 - 247 HP

Frame

Front Frame Structure - Height - 1.1 Feet

Front Frame Structure - Width - 1 ft.

Circle - Diameter - 60.2 inches

Drawbar - height - 6 inches

Front Axle - Center Height - 23.5 inches

Circle - blade thickness - 1.6 inches

Front axle - overall swing to the side - 32 degrees

Drawbar - Thickness - 0.5 inches

Drawbar - Width - 3 inches

Top / Bottom Front - 12 inches wide

Top / Bottom Front - 0.9in Thickness

Front axle - wheel tilt - left / right - 18 degrees

Circle - Height - 5.4 inches

Power train

Brakes - Parking - Multifunctional Oil Disc

Brakes - Service - Multi-disc

Transmission - APECS, Direct Drive, Powershift

Forward / Reverse Gear - 8 Forward / 6 Reverse

Brakes - Secondary - Bypass

Brakes - Maintenance - Surface Area - 3565in2

Weights

Weight in working condition - usually equipped

45917lb

Hydraulic system

Pump type - Variable piston

Chain type - Parallel

Maximum system pressure - 3,500 psi

Pump performance - 55.7 gpm

Tank capacity - 16.9gal

Reserve pressure - 885 psi

Plow blade

Blade width - 12 feet in

Arc radius - 16.3in

Throat cleansing - 6.5in

Cutting width - 6in

Cutting edge thickness - 0.6in

End Bit - Width - 6in

End Bit - Thickness - 0.6in

Moldboard - Height - 24in

Moldboard - Thickness - 0.9in

Blade Traction - GVW Base - AWD - 36341lb

Bollard pull - maximum gross weight - gross  - 49630lb

Pressure Down Blades - Base Weight - AWD - 18411lb

Blade Lowering Pressure - Maximum Gross Weight - AWD - 29308lb

Moldboard - blade width - 12 feet in

Dimensions

Height - Cab Top - 10.9 feet in

Width - External Rear Tires - 98.9in

Height - Top of Cylinders - 120in

Ground clearance - Rear axle - 13.3in

Length - counterweight to ripper - 399in

Width - External Front Tires - 98.9in

Length - Front Axle to Tandem - 241in

Length - from front tire to rear of machine - 351in

Length - from front axle to blade - 100in

Length - between tandem axles - 60in

Width - Tire Lines - 84.3in

Height - Exhaust Pipe - 128in

Height - center of front axle - 23.5in

Operational characteristics

Top speed forward - 29mph

Maximum Speed ​​- Reverse - 23mph

Turn Radius - External Front Tires - 25.6 feet in

Steering Range - Left / Right - 50 degrees

Joint Angle - Left / Right - 20 degrees

Forward - 8 - 29mph

Forward - 7 - 19.9mph

Forward - 6 - 4.5mph

Forward - 5 - 10.6mph

Forward - 4th - 6.9mph

Forward - 3rd - 5mph

Forward - 2nd - 3.4mph

Forward - 1st - 2.5mph

Reverse - 6 - 23mph

Reverse - 5 - 15.7mph

Reverse - 4th - 8.4mph

Reverse - 3rd - 5.4mph

Reverse - 2nd - 3.7mph

Reverse - 1st - 2mph

Standards

the brakes - ISO 3450

ROPS / FOPS - ISO 3471 / ISO 3499

sound - ISO 6394; ISO 6395

Steering - ISO 5010

Top-up Service

Cooling system - 15gal

Hydraulic System - Total - 26.4gal

Machine oil - 7.9gal

Hydraulic System - Tank - 16.9gal

Tandem Case - Each - 20gal

Drive housing - 1.8gal

Front wheel spindle bearing housing - 0.2gal

Fuel tank capacity - 104gal

Transmission - Differential - Final Drives - 18.5gal

Diesel exhaust fluid - 5.8gal

Blade range 

Circle Shift - Right - 28.7in

Circle Shift - Left - 27.4in

Side Shift - Right - 26in

Side Shift, Left Side - 20.1in

Blade Tip Range - Forward - 40 degrees

Blade Tip Range - Back - 5 degrees

The maximum shoulder extension outside the tires is on the right - 77.9in

The maximum shoulder extension outside the tires is left - 70.5in

Maximum Rise Above Ground - 18.9in

Maximum cutting depth - 28.1in

Maximum blade angle - 90 degrees

Baking powder

Front V-Type - Working Width - 47.4in

Back - Scarifier Shank Holders - 9

Mid, V-Type - Scarifier Shank Holders - eleven

Anterior, V-shaped, 5 or 11 tooth - working width - 40.6in

Anterior, V-shaped, 5 or 11 tooth - maximum scarification depth - 18.4in

Front, V, 5 or 11 teeth - Scarifier Shank Holders - 5/11

Anterior, V-shaped, 5 or 11 tooth - The distance between the holders of the scarifier shank - 4.6in

Medium V-Type - Working Width - 46.6in

Mid, V-Type - maximum scarification depth - 11.5in

Mid, V-Type - Distance between the holders of the scarifier shank - 4.6in

Rear - Working Width - 84in

Back - maximum scarification depth - 16.8in

Back - The distance between the holders of the scarifier shank - 10.5in