Caterpillar ASPHALT PAVERS AP500F - catalog of spare parts
The AP500F is a medium-sized wheeled paver that offers versatility for highways, rural roads, streets, and other medium-sized projects.
The C4.4 engine delivers 106 kW (142 imperial hp, 144 metric hp)) at 2,200 rpm and meets regional emission requirements, including US EPA Tier 4 Final standards and EU Stage IV standards.
Eco mode uses engine speeds of 1,650 rpm and reduces fuel consumption by 5% compared to Cat E Series Pavers, and also reduces noise levels even further.
When the automatic engine speed control is activated, the engine speed is reduced to idle speed of 1000 rpm when the drive lever is moved to the neutral position, or to 1300 rpm when the screed heating is active.
3P8681 | CONE | Caterpillar | View |
3P8680 | 3P8680 | Caterpillar | View |
ENHANCED ECO-MODE
Eco mode and automatic engine speed control, when activated together, change the engine speed depending on load factors. When activated, the engine will operate at 1650 rpm when laying. If the upper power threshold is exceeded, the engine speed will increase to 2,200 rpm and will remain there until the need drops below the threshold and remains there for 30 seconds. This technological advancement helps ensure reliable performance.
SILENT HEATING
The quiet thermal mode operates at an engine speed of 1300 rpm and provides heating in less than 15 minutes.
QUICK HEATING
Rapid heating mode provides a warm-up time of less than 35 minutes when using a package for laying a wide pavement.
TEMPERATURE RANGES
Three preset heating options provide a wide range of temperatures for different mix designs; Low - 110 degrees C or 230 degrees Fahrenheit, medium - 130 degrees C or 266 degrees Fahrenheit, high - 160 degrees C or 320 degrees Fahrenheit.
BETTER VISIBILITY, EXCLUSIVE COMFORT
Dual independent workstations may extend beyond circular visibility. The low-profile cooling system, installed in front, improves visibility forward, and the redesigned auger assembly optimizes visibility to the height of the material in front of the coupler. The option of heated seats, multi-seat adjustment and sloping consoles allow the operator to provide comfort throughout the day. In addition, the overhead cooling system directs smoke, hot air and fan noise from the crew for a cooler and quieter working environment.
PARK MANAGEMENT SYSTEM
An exclusive ventilation system pulls the fumes from the conveyor tunnel as well as from the auger chamber and redirects them from the operator for a more comfortable working environment.
THE ONLY SENSORY WORK
The one-touch functions for an automatic filling system, activation of the supply system and bunker control allow operators to concentrate on truck exchanges and other tasks of the working site to increase efficiency.
SIMPLE TECHNOLOGY
Technology helps operators perform. Intuitive symbols and large graphics simplify operation, and an interactive touch-screen LCD display that allows you to activate the generator, adjust the temperature of the screed and adjust the height of the mixture helps to increase efficiency.
AUTOMATIC FEEDING SYSTEM
The auto-fill system makes it easy to start, alternating between conveyors and augers, until the mixture reaches the sensor point.
The ONLY FEED SYSTEM
One switch automatically activates the entire supply system for increased efficiency.
CONTROL OF ONE TOUCH
The wings of the bunker and the hydraulic apron can be folded with one touch and released. The system can be configured to activate the left or right wing or the front hydraulic apron independently or together.
Cleaning mode and warm up
This feature activates augers, conveyors and protective bar (if any) at a reduced speed, which allows the use of anti-adhesives that help prevent material accumulation.
HIGH MIX ADJUSTMENT
Adjusting the height of the mixture before the coupler can be changed on the tractor`s LCD display to increase versatility if necessary.
HYDRAULIC EXTENSIONS OF THE MAIN FRAME
Additional 457 mm (18 ") additional hydraulic extenders are attached to the auger assembly and provide a smooth flow of material to the extenders. They are reduced with the help of extenders with decreasing laying width.
OPTIONS FOR MULTIPLE FEED SENSORS
The feed system can be configured to automatically operate with 0, 2, or 4 feed sensors. When stacking with 0 sensors due to a malfunction, simply install an automatic feed system and adjust the mix height setting, no need to switch the manual switch as required in previous models.
SIMPLE SERVICE
Support plates that do not require hardware simplify maintenance requirements, and underside fasteners for chain guards eliminate bolt wear and material buildup for easier replacement.
SWING CURRENT SYSTEM
A position sensor, located in the left-hand steering cylinder, helps maintain a constant speed when cornering by adjusting the speed of the drive motors in accordance with the angle of rotation of the front wheels. This unique system provides better rug quality and less wear on the drive system.
FOUR-WHEEL DRIVE
Provides power to the front wheels of the trolley for extra traction. Special pump provides an increase in torque by 50% compared with previous models.
SCREED HEAT TECHNOLOGY
Exclusive zone monitoring allows you to continue heating in the event of a temperature sensor failure. The system also monitors the heating elements for faults, helping to eliminate unnecessary replacement.
EASY ADJUSTMENT
The ability to adjust the ratio of the feed system from the screed provides versatility. Standard hydraulic adjustment of the extension height, slope and crown allows you to adjust on the go with the standard and maximum width of the installation.
2-speed proportional control
Exclusive two-speed proportional control of the extension provides a slower speed for precise control around obstacles and quick response with increasing laying width.
BETTER EFFICIENCY
Heating elements extend for easy replacement, no need to remove the tie. In addition, the treated screeds facilitate the replacement and alignment of screeds.
VARIANT SCREEN DRUM
Screeds equipped with a protective strip increase the density, as they enclose the material under the plates. Three tamper stroke settings of 2, 4 and 7 mm, as well as a variable tamper speed from 700 to 1800 rpm, ensure versatility of application.
WIDE COMMUNITY PACKAGES
Exclusive power controls make it easy to adjust across the entire width of the road surface for better texture of the mat. The innovative design uses the expander slope to attach wide width pavement packages, eliminating the need for additional lifting devices.
EASY OPERATION
The F Series Pavers allow you to control Cat Grade Control from either of two tractors or two screeds. The split screen mode can be configured to control each side of the tie and allows one person to control the operation.
EXACT CONTROL
More precise control maximizes blend usage and saves money. True averaging occurs with acoustic sensors that use 5 transducers, 2 readings are discarded and 3 are averaged. 10-point auto-calibration eliminates overshoot and override from a single calibration point. Crossover, incline and height are maintained with height adjustments. A true 9-meter (30-foot) sonic averaging beam changes the movement of the tow point by 1/3 of the total deviation of the slope.
HIGHLY RELIABLE
Watertight displays, factory installed components and sequential routing provide performance. Sealed components withstand heat, moisture and vibration. Built-in temperature sensors provide better reliability than collateral type sensors.
WEIGHTS
Operating Weight - Paver Only |
29020.0 lb |
Operating Weight - SE50 V Screed only |
7239.0 lb |
Operating Weight - SE50 VT Screed only |
7695.0 lb |
Shipping Weight - Paver Only |
28599.0 lb |
OPERATING SPECIFICATIONS
Standard Paving Range - SE50 V, SE50 VT |
2.55 - 5.0 m (8` 4" - 16` 4") |
Hopper Capacity |
219.0 ft³ |
Inside Turn Radius |
1.15 ft |
Maximum Paving Speed - With Tamper Bar Screed |
82.0 ft/min |
Maximum Paving Speed - With Vibratory Screed |
250.0 ft/min |
Maximum Travel Speed |
10.0 mile/h |
Maximum Paving Width - SE50 V |
21.3 ft |
Maximum Paving Width - SE50 VT |
21.3 ft |
Maximum Throughput Capacity |
1288.0 tonnes/hr |
ENGINE
Gross Power |
142.0 HP |
Engine Model |
Cat C4.4 with ACERT |
SERVICE REFILL CAPACITIES
Fuel Tank Capacity |
47.0 gal (US) |
DEF Tank |
5.0 gal (US) |
Specifications
Engine
Gross Power
142hp
Engine Model
Cat C4.4 with ACERT
Weights
Shipping Weight - Paver Only
28599lb
Operating Weight - Paver Only
29020lb
Operating Weight - SE50 V Screed only
7239lb
Operating Weight - SE50 VT Screed only
7695 lb
Operating Specifications
Maximum Travel Speed
10mph
Maximum Paving Speed - With Vibratory Screed
250 ft/min
Maximum Paving Speed - With Tamper Bar Screed
82 ft/min
Inside Turn Radius
1.2ft in
Maximum Throughput Capacity
1288 tonnes/hr
Standard Paving Range - SE50 V, SE50 VT
2.55 - 5.0 m (8` 4" - 16` 4")
Maximum Paving Width - SE50 V
21.3ft in
Maximum Paving Width - SE50 VT
21.3ft in
Hopper Capacity
219 ft
Service Refill Capacities
DEF Tank
5gal
Fuel Tank Capacity
47gal