Caterpillar ASPHALT PAVER AP555F - catalog of spare parts
The AP555F is a mid-sized, rubber track paver that excels on highways, streets and other urban work sites. It`s high travel speed, excellent flotation, and superior traction deliver superb mobility.
The C4.4 engine provides 106 kW (142 imperial hp, 144 metric hp) and meets regional emission requirements, including US EPA Tier 4 Final standards and EU Stage IV standards.
Eco mode uses engine speeds of 1,650 rpm and reduces fuel consumption by 5% compared to Cat E Series Pavers, and also reduces noise levels even further.
When the automatic engine speed control is activated, the engine speed is reduced to idle speed of 1000 rpm when the drive lever is moved to the neutral position, or to 1300 rpm when the screed heating is active.
Choose ASPHALT PAVER AP555F section:
ENHANCED ECO-MODE
Eco mode and automatic engine speed control, when activated together, change the engine speed depending on load factors. When activated, the engine will operate at 1650 rpm when laying. If the upper power threshold is exceeded, the engine speed will increase to 2,200 rpm and will remain there until the need drops below the threshold and remains there for 30 seconds. This advanced technological advancement ensures reliable performance.
SILENT HEATING
The silent heating mode operates at a rotational speed of 1300 rpm and provides warming up of the screeds in less than 15 minutes.
QUICK HEATING
Rapid heating mode provides a warm-up time of less than 35 minutes when using a package for laying a wide pavement. Rapid heating does not heat up faster than quiet heating when the screed has a standard extension width.
TEMPERATURE RANGES
Three preset heating options provide a wide range of temperatures for different mix designs; Low - 110 degrees C or 230 degrees Fahrenheit, medium - 130 degrees C or 266 degrees Fahrenheit, high - 160 degrees C or 320 degrees Fahrenheit.
BETTER VISIBILITY, EXCLUSIVE COMFORT
Dual independent workstations may extend beyond circular visibility. The low-profile cooling system, installed in front, improves visibility forward, and the redesigned auger assembly optimizes visibility to the height of the material in front of the coupler. The option of heated seats, multi-seat adjustment and sloping consoles allow the operator to provide comfort throughout the day. The overhead cooling system directs smoke, hot air and fan noise from the crew for a cooler and quieter work environment.
PARK MANAGEMENT
An exclusive ventilation system picks up pairs from the conveyor tunnel, as well as from the auger chamber, and redirects them from the operator for a more comfortable working environment.
THE ONLY SENSORY WORK
The one-touch functions for an automatic filling system, activation of the supply system and bunker control allow operators to focus on truck exchanges and other tasks to improve efficiency.
SIMPLE TECHNOLOGY
Technology helps operators perform. Intuitive symbols and large graphics simplify operation, and an interactive LCD display with a touch screen that allows you to activate the generator, adjust the temperature of the screed and adjust the height of the mixture, increases efficiency.
AUTOMATIC FEEDING SYSTEM
The automatic filler feed system makes it easy to start, alternating between conveyors and augers, until the mix height reaches the sensor set point. This unique system eliminates manual activation and ongoing monitoring for more stable operation.
The ONLY FEED SYSTEM
Two augers and two conveyors can be activated automatically with a single switch for easy setup. Each auger and each conveyor can operate independently of each other when necessary.
CONTROL OF ONE TOUCH
The wings of the bunker and the hydraulic apron can be folded with one touch and released. The system can be configured to activate the left or right wing or the front hydraulic apron independently or together.
Cleaning mode and warm up
This feature activates augers, conveyors and protective bar (if any) at a reduced speed, which allows the use of anti-adhesives that help prevent material accumulation.
HIGH MIX ADJUSTMENT
Adjusting the height of the mixture before the coupler can be changed on the tractor`s LCD display to increase versatility if necessary.
HYDRAULIC EXTENSIONS OF THE MAIN FRAME
Additional 457 mm (18 ") additional hydraulic extenders are attached to the auger assembly and provide a smooth flow of material to the extenders. They are reduced with the help of extenders with decreasing laying width.
OPTIONS FOR MULTIPLE FEED SENSORS
The feed system can be configured to automatically operate with 0, 2, or 4 feed sensors. When stacking with 0 sensors due to a malfunction, simply install an automatic feed system and adjust the mix height setting, no need to switch the manual switch as required in previous models.
SIMPLE SERVICE
Support plates that do not require equipment simplify replacement, and mounting on the underside for protective circuits eliminates bolt wear and material buildup for easier maintenance.
SPECTACLE
Mobil-Trac undercarriage minimizes the movement of the tow point. Front and rear carts allow you to overcome obstacles and maintain contact with the ground. The smooth tape version works well on soft base materials and fresh mats. The design of the treadmill copes with the loose surface / transportation conditions.
STRENGTH
Self-locking batteries, center guides and sturdy internal strap cables ensure durability. Components are rubber coated to shed asphalt and prevent buildup.
SCREED HEAT TECHNOLOGY
Exclusive zone monitoring allows you to continue heating in the event of a temperature sensor failure. The system also monitors the heating elements for malfunctions and helps eliminate unnecessary replacement.
EASY ADJUSTMENT
The ability to adjust the ratio of the feed system from the tie provides additional versatility. Standard power adjustment for height, tilt and extension crown allows you to adjust on the go with standard and maximum installation widths.
2-speed proportional control
Exclusive two-speed proportional control of the extension provides a lower speed for precise control of obstacles and quick response with increasing laying width.
SIMPLE REPLACEMENT
Heating elements extend for easy replacement, no need to remove the tie. In addition, machined screeds facilitate the replacement and alignment of screeds.
VARIANT SCREEN DRUM
Screeds equipped with a protective strip increase the density, as they enclose the material under the plates. Three stroke settings of 2, 4 and 7 mm and a variable tamper speed from 700 to 1800 rpm provide versatility.
WIDE COMMUNITY PACKAGES
Exclusive power controls make it easy to adjust across the entire width of the road surface for better texture and quality mats. The innovative design uses the expander slope for attaching wide width pavements and eliminates the need for additional lifting devices.
EASY OPERATION
The F Series Pavers allow you to control Cat Grade Control from either of two tractors or two screeds. The split screen mode can be configured to control each side of the tie, allowing you to control one person.
EXACT CONTROL
More precise control maximizes blend usage and saves money. True averaging using sound sensors that use 5 transducers, 2 readings are discarded and 3 are averaged. 10-point auto-calibration eliminates the possibility of over / under-adjustment from one calibration point. Crossover, slope and height are maintained by adjusting the height. A true 9-meter (30-foot) sonic averaging beam changes the movement of the tow point by 1/3 of the total deviation of the slope.
HIGHLY RELIABLE
Watertight displays, factory installed components and sequential routing provide performance. Sealed components withstand heat, moisture, and vibration, and built-in temperature sensors provide better reliability than flip-type sensors.
Standard Paving Range - SE50 V, SE50 VT |
2.55 - 5.0 m (8` 4" - 16` 4") |
Inside Turn Radius |
1.5 ft |
Maximum Paving Speed - With Tamper Bar Screed |
82.0 ft/min |
Maximum Paving Speed - With Vibratory Screed |
210.0 ft/min |
Maximum Travel Speed |
7.0 mile/h |
Hopper Capacity |
219.0 ft³ |
Maximum Paving Width - SE50 V |
21.3 ft |
Maximum Paving Width - SE50 VT |
24.7 ft |
Maximum Throughput Capacity |
1288.0 tonnes/hr |
ENGINE
Gross Power |
142.0 HP |
Engine Model |
Cat C4.4 with ACERT |
SERVICE REFILL CAPACITIES
Fuel Tank Capacity |
47.0 gal (US) |
DEF Tank |
5.0 gal (US) |
WEIGHTS
Operating Weight - Paver Only |
30430.0 lb |
Operating Weight - SE50 V Screed only |
7239.0 lb |
Operating Weight - SE50 VT Screed only |
7695.0 lb |
Shipping Weight - Paver Only |
30009.0 lb |
Specifications
Engine
Gross Power
142hp
Engine Model
Cat C4.4 with ACERT
Weights
Shipping Weight - Paver Only
30009lb
Operating Weight - Paver Only
30430lb
Operating Weight - SE50 V Screed only
7239lb
Operating Weight - SE50 VT Screed only
7695 lb
Operating Specifications
Maximum Travel Speed
7mph
Maximum Paving Speed - With Vibratory Screed
210 ft/min
Maximum Paving Speed - With Tamper Bar Screed
82 ft/min
Inside Turn Radius
1.5ft in
Maximum Throughput Capacity
1288 tonnes/hr
Standard Paving Range - SE50 V, SE50 VT
2.55 - 5.0 m (8` 4" - 16` 4")
Maximum Paving Width - SE50 V
21.3ft in
Maximum Paving Width - SE50 VT
24.7ft in
Hopper Capacity
219 ft
Service Refill Capacities
DEF Tank
5gal
Fuel Tank Capacity
47gal