Caterpillar WHEEL TRACTOR-SCRAPER 623K - catalog of spare parts
Fast loading, high speeds and the ability to load and unload on-the-go result in reduced cycle times, which allows Cat wheeled tractor-tractors to constantly deliver high performance with minimal cost per ton. Tractor performance improvement — the filter unit located at the rear of the engine compartment has undergone improvements for ease of maintenance by lifting the filter unit up for easier access.
Choose WHEEL TRACTOR-SCRAPER 623K section:
Motor overspeed protection - in case of engine overspeed, the compression brake or brakes are automatically activated without operator intervention. The machine determines the overspeed condition based on the acceleration speed and automatically activates the compression brakes.
Advanced hitch - thanks to technology similar to Cat® Advanced Ride Management seat suspension, this software allows the cushion suspension device to prevent the final stroke, being able to predict the final stroke events and control the speed of the damping. The desired result is improved hitch repair, reduced maintenance and an improved operator ride in rough conditions.
High Pressure Steering - The design of the 620K Series steering system requires significantly less effort when taxiing. Reduced steering effort will reduce operator fatigue and increase its efficiency, which will lead to possible higher production rates at the end of the operating cycle.
The Load Assist - 623K option is now available with the Load Assist option, such as 621K and 627K.
Overflow protection - Now open bowls are now standard with overflow protection on the side of the bowl to prevent material from entering through the edges of the bowl and falling onto the rods when the material falls between the edge of the bowl and the edge, resulting in reduced cycle times.
Auto Stall - in cold weather conditions, the car will use the Auto Stall function to help heat up the gear oil faster, which will cause the car to switch from the torque converter drive (2nd gear) faster than on previous models.
Differential lock protection (standard) —This standard feature allows the machine to prevent the differential lock from being activated when damage may occur.
Improved cab - The interior of the K-Series cabins has improved the convenience and visibility of the operator by changing the dashboard design and key layout.
Car speed limit - this feature is used to select the top gear. If it is necessary to limit the maximum speed of the machine, the operator can select the maximum speed using the display or the maximum speed can be set to ET. This will allow the car to find the right gear that is best for the engine and transmission. Allowing the engine and transmission to choose the right gear to pull the load in most cases, resulting in a lower engine load factor and a reduction in the number of burned fuel verses using top gear selection, which required the machine to operate at engine speeds at high revs or close to by him.
Stroke speed control - Stroke speed control sets the operator the desired maximum speed if conditions on the working platform or segment speed limits require a speed that is less than full. The machine speed limit is intended for use when the maximum speed is to be limited for longer periods of time, and the travel speed control is for use when the maximum speed is to be reduced for shorter segments or intermediate periods of time. The operator can set the desired maximum speed, and the car will find the right gear, which is best suited for the engine and transmission. Allowing the engine and transmission to select the right gear to pull the load will in most cases reduce the engine load factor and reduce fuel consumption when choosing the top gear.
GENERAL
180° Curb-to-Curb Turning Width |
38.71 ft |
Elevator Flight Spacing |
20.0 in |
Fuel Tank Refill Capacity - Scraper |
201.0 gal (US) |
Maximum Depth of Cut |
10.3 in |
Maximum Depth of Spread |
18.3 in |
Maximum Floor Opening |
4.4 ft |
Number of Flights |
15 |
Operating Weight - Empty |
88061.0 lb |
Overall Length |
45.18 ft |
Overall Shipping Height |
12.37 ft |
Overall Width |
11.71 ft |
Rated Load |
25 038 kg (55,200 lb); 25.1 tonnes (27.6 tons) |
Scraper Capacity - Heaped |
23.0 yd³ |
Scraper Capacity - Struck |
18.8 yd³ |
Tires - Scraper |
33.25R29**E3 |
Tires - Tractor Drive |
33.25R29**E3 |
Top Speed - Loaded |
33.5 mile/h |
Width - Cut |
10.3 ft |
ENGINE
Flywheel Power - Tractor/Scraper |
304 kW (407 hp) |
Engine Model |
Cat C13 ACERT™ |
Flywheel Power - Tractor |
407.0 HP |
Note |
C13 ACERT engine emits equivalent to U.S. EPA Tier 2/EU Stage II or U.S. EPA Tier 3/EU Stage III. |
Rated Engine RPM |
2000.0 r/min |
TRANSMISSION
Top Speed - Loaded |
33.5 mile/h |
SCRAPER BOWL
Scraper Capacity - Heaped |
23.0 yd³ |
SERVICE REFILL CAPACITIES
Fuel Tank |
216.09 gal (US) |
Crankcase |
8.08 gal (US) |
Cooling System |
11.89 gal (US) |
Hydraulic System |
21.926 gal (US) |
Transmission System |
24.76 gal (US) |
DIMENSIONS
Height - Overall Shipping |
158.9 in |
Length - Overall Machine |
542.0 in |
Width - Overall Machine |
141.1 in |
Height - Top of Cab |
142.6 in |
Height - Scraper Blade Maximum |
20.5 in |
Width - Tractor |
133.1 in |
Width - Inside of Bowl |
120.0 in |
Width - Outside Rear Tires |
128.9 in |
Front of Tractor to Front Axle |
122.8 in |
Wheel Base |
329.5 in |
Rear Axle - Rear of Machine |
89.7 in |
Ground Clearance - Tractor |
21.9 in |
Axle to Vertical Hitch Pin |
17.0 in |
Height - Top of Elevator |
148.3 in |
Width - Overall Machine - Ladder Down |
149.2 in |
Width - Rear Tire Centers |
90.2 in |
CAB
Exterior Sound Level |
The exterior sound power level for the standard machine (ISO 6393) is 111.5 dB(A). |
ROPS/FOPS |
Meets ISO standards |
SAFETY CRITERIA COMPLIANCE STANDARDS
Brakes |
ISO 3450:2011 |
Falling Object Protective Structure (FOPS) |
ISO 3449:2005 Level II |
Reverse Alarm |
ISO 9533:2010 |
Rollover Protection Structure (ROPS) |
ISO 3471:2008 for up to 17 084 kg (37,664 lb) |
Seat Belt |
SAE J386:JUN1985 |
Steering System |
ISO 5010:2007 |
TRAVEL SPEEDS - RUNOUT
Transmission Gear - Eighth |
33.5 mile/h |
Transmission Gear - Fifth |
13.6 mile/h |
Transmission Gear - First |
3.1 mile/h |
Transmission Gear - Fourth |
10.1 mile/h |
Transmission Gear - Reverse |
5.7 mile/h |
Transmission Gear - Second |
5.5 mile/h |
Transmission Gear - Seventh |
24.8 mile/h |
Transmission Gear - Sixth |
18.4 mile/h |
Transmission Gear - Third |
7.5 mile/h |
IMPLEMENT CYCLE TIMES
Bowl Lower |
3.5 s |
Bowl Raise |
3.0 s |
Ejector Extend |
6.45 s |
Ejector Retract |
9.7 s |
Dimensions
General
Overall Length 45.18ft in
Overall Width 11.71ft in
Specifications
Engine
Engine Model Cat C13 ACERT
Note
Cat C13 ACERT engine meets U.S. Environmental Protection Agency (EPA) Tier 4 Final/EU Stage IV engine emission standards.
Flywheel Power - Tractor/Scraper 304 kW (407 hp)
Rated Engine RPM 2000rpm
Flywheel Power – Tractr 407hp
Transmission
Top Speed – Loaded 33.5mph
Dimensions
Wheel Base 27.5ft in
Height - Top of Cab 11.9ft in
Length - Overall Machine 542in
Width - Outside Rear Tires 128.9in
Width - Inside of Bowl 120in
Height - Overall Shipping 158.9in
Width – Tractor 133.1in
Width - Overall Machine 141.1in
Ground Clearance – Tractor 21.9in
Front of Tractor to Front Axle 122.8in
Height - Scraper Blade Maximum 20.5in
Rear Axle - Rear of Machine 89.7in
Width - Overall Machine - Ladder Down 149.2in
Height - Top of Elevator 148.3in
Width - Rear Tire Centers 90.2in
Axle to Vertical Hitch Pin 17in
Service Refill Capacities
Cooling System 11.9gal
Fuel Tank 216.1gal
Crankcase 8.1gal
Hydraulic System 22gal
Diesel Exhaust Fluid 8.1gal
Transmission System 24.8gal
Cab
ROPS/FOPS Meets SAE and ISO standards
Exterior Sound Level
The exterior sound power level for the standard machine (ISO 6393) is 111.5 dB(A).
Scraper Bowl
Scraper Capacity – Heaped 23yd3
General
Tires - Tractor Drive 33.25R29**E3
Elevator Flight Spacing 20in
Number of Flights 15
Maximum Floor Opening 4.4ft in
Fuel Tank Refill Capacity – Scraper 201gal
Overall Width 11.8ft in
Overall Shipping Height 12.4ft in
Scraper Capacity – Struck 18.8yd3
Scraper Capacity – Heaped 23yd3
Rated Load 25 038 kg (55,200 lb); 25.1 tonnes (27.6 tons)
Width – Cut 10.3ft in
Maximum Depth of Cut 10.3in
Maximum Depth of Spread 18.3in
Top Speed – Loaded 33.5mph
180 degrees Curb-to-Curb Turning Width 38.8ft in
Tires – Scraper 33.25R29**E3
Operating Weight – Empty 88061lb
Overall Length 45.2ft in
Implement Cycle Times
Bowl Raise 3 s
Bowl Lower 3.5 s
Ejector Extend 6.45 s
Ejector Retract 9.7 s
Safety Criteria Compliance Standards
Rollover Protection Structure (ROPS) ISO 3471:2008 for up to 17 084 kg (37,664 lb)
Falling Object Protective Structure (FOPS) ISO 3449:2005 Level II
Brakes ISO 3450:1996
Steering System ISO 5010:2007
Seat Belt SAE J386:JUN1985
Reverse Alarm ISO 9533:2010
Travel Speeds – Runout
Transmission Gear – First 3.1mph
Transmission Gear – Second 5.5mph
Transmission Gear – Third 7.5mph
Transmission Gear – Fourth 10.1mph
Transmission Gear – Fifth 13.6mph
Transmission Gear – Sixth 18.4mph
Transmission Gear – Seventh 24.8mph
Transmission Gear – Eighth 33.5mph
Transmission Gear – Reverse 5.7mph